How to remove the Rear Shock Absorber on a Honda Fit?

Loosen the rear wheel lug nuts. Raise the rear of the vehicle and support it securely on jackstands. Block the front wheels to prevent the vehicle from rolling. Remove the wheel. Support the rear axle beam with a floor jack placed under the coil spring pocket. Remove the access panel in the luggage compartment and unscrew the shock absorber upper mounting nut. Hold the shock absorber piston rod with an Allen wrench while loosening the upper mounting nut. Remove the washer and mounting cushion. Unscrew the shock absorber lower mounting bolt and nut and remove the shock absorber. Installation is the reverse of removal. Be sure the mounting cushions and upper washer are properly installed on the piston rod. Remove the plastic retainers and take off the steering column U-joint cover. Then tighten the NEW upper mounting nut to the torque. Raise the floor jack to simulate normal ride height, then tighten the NEW lower mounting bolt to the torque. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts to the torque.

How Do I Replace a Strut and Coil Springs on a Honda Fit?

Remove the cowl cover, lower the cowl, and loosen the wheel lug nuts. Raise and support the vehicle, remove the wheels, and unplug the wheel speed sensor wiring along with the brake hose from the strut. Remove the wheel speed sensor from the steering knuckle, disconnect the stabilizer bar link from the strut, and remove strut-to-knuckle nuts and bolts. Separate the strut from the steering knuckle, hold the strut piston rod and remove the upper mounting nut and washer. Remove the damper mounting base and strut/spring assembly, and check the strut body and coil spring for damage. Place the strut cushion onto the strut and guide it into place. Install the mounting base, washer and nut, and raise the suspension with the jack. Tighten strut-to-knuckle bolts and nuts. Connect the stabilizer bar link and tighten the nut. Hold the strut piston rod and tighten the upper mounting nut, then put in the wheel and lug nuts, lower the vehicle, and tighten the lug nuts. Check and adjust the front-end alignment.

How Should I Handle Strut or Coil Spring Wear on Honda Fit?

If signs of wear are present, check cost and availability of parts before disassembling. Remove strut and spring assembly, then mounting base. Install spring compressor and relieve pressure from upper spring seat. Remove piston rod nut and strut bearing. Inspect bearing for smooth operation. Replace rubber spring seat if necessary. Carefully lift compressed spring from assembly. Slide dust boot off piston rod. Check lower insulator for wear, cracking and hardness. Replace if necessary. For reassembly, set lower insulator into position. Extend damper rod and install dust boot. Place coil spring onto lower insulator. Install upper insulator and spring seat. Install upper spring seat and strut bearing. Install strut piston rod nut and tighten. Remove spring compressors. Install mounting base and strut coil spring assembly.

Genuine Honda Fit Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Shock Absorbers found

View related parts
Honda Fit Shock Absorber Unit, Rear
Part Number: 52611-T5R-A02
$182.58 MSRP: $260.08
You Save: $77.50 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2016 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX | KA 6MT, KA CVT
View related parts
Honda Fit Damper Unit, Rear
Part Number: 52611-T5R-A51
$182.64 MSRP: $260.17
You Save: $77.53 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock, Shock Absorber
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA 6MT, KA CVT
View related parts
Honda Fit Shock Absorber Unit, Right Front
Part Number: 51611-T5R-A04
$209.98 MSRP: $299.12
You Save: $89.14 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Replaces: 51611-T5R-A03, 51611-T5R-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2016 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX | KA 6MT, KA CVT
View related parts
Honda Fit Shock Absorber Unit, Right Front
Part Number: 51611-TK6-A02
$220.78 MSRP: $314.50
You Save: $93.72 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber Unit, Left Front
Part Number: 51621-T5R-A04
$209.98 MSRP: $299.12
You Save: $89.14 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Replaces: 51621-T5R-A02, 51621-T5R-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2016 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX | KA 6MT, KA CVT
View related parts
Honda Fit Shock Absorber, Rear
Part Number: 52610-TK6-306
$230.77 MSRP: $328.73
You Save: $97.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Replaces: 52610-TK6-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber, Rear
Part Number: 52610-TK6-308
$230.77 MSRP: $328.73
You Save: $97.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock, Shock Absorber
- Position: Rear
- Replaces: 52610-TK6-A51
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Damper Assembly, Left Front
Part Number: 51620-TK6-A61
$489.49 MSRP: $706.33
You Save: $216.84 (31%)
ADD TO CART
Product Specifications
- Other Name: Strut Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door Sport | KA 5AT
View related parts
Honda Fit Shock Absorber Assembly, Rear
Part Number: 52610-SLN-A04
$246.62 MSRP: $351.32
You Save: $104.70 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Replaces: 52610-SLN-A02, 52610-SLN-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber Unit, Left Front
Part Number: 51606-SLN-A13
$205.94 MSRP: $293.37
You Save: $87.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Replaces: 51606-SLN-A12
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT
View related parts
Honda Fit Damper Unit, Front Right
Part Number: 51611-T5R-A51
$193.04 MSRP: $274.98
You Save: $81.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA 6MT, KA CVT
View related parts
Honda Fit Shock Absorber Unit, Left Front
Part Number: 51621-TK6-A02
$220.76 MSRP: $314.47
You Save: $93.71 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber Unit, Right Front
Part Number: 51611-TK6-A11
$201.99 MSRP: $287.74
You Save: $85.75 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2012 Honda Fit | 5 Door FIT | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber, Rear
Part Number: 52610-TK6-307
$230.77 MSRP: $328.73
You Save: $97.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock, Shock Absorber
- Position: Rear
- Replaces: 52610-TK6-A13
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2012 Honda Fit | 5 Door FIT | KA 5AT, KA 5MT
View related parts
Honda Fit Damper Unit, Rear Front
Part Number: 51611-TK6-A51
$295.10 MSRP: $420.37
You Save: $125.27 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Damper Unit, Rear Front
Part Number: 51611-TK6-A71
$295.10 MSRP: $420.37
You Save: $125.27 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door FIT | KA 5AT, KA 5MT
View related parts
Honda Fit Damper Unit, Front Left
Part Number: 51621-T5R-A51
$193.04 MSRP: $274.98
You Save: $81.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA 6MT, KA CVT
View related parts
Honda Fit Shock Absorber Unit, Left Front
Part Number: 51621-TK6-A11
$216.54 MSRP: $308.47
You Save: $91.93 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2012 Honda Fit | 5 Door FIT | KA 5AT, KA 5MT
View related parts
Honda Fit Damper Unit, Left Front
Part Number: 51621-TK6-A51
$294.78 MSRP: $419.92
You Save: $125.14 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door Sport | KA 5AT, KA 5MT
View related parts
Honda Fit Shock Absorber, Rear
Part Number: 52610-TK6-309
$230.77 MSRP: $328.73
You Save: $97.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Replaces: 52610-TK6-A71
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door FIT | KA 5AT, KA 5MT

| Page 1 of 3 |Next >

1-20 of 52 Results

Honda Fit Shock Absorber

The Shock Absorber in Honda Fit vehicles is an important part and detains a pivotal position in the suspension system of the vehicle subsequent to the struts. Using this design, kinetic energy is turned to heat hence minimizing the effects of the rough terrain on the vehicle and providing a good handling of the same. Yearly, Honda Fit vehicles have employed Shock Absorbers of different types such as twin-tube and mono-tube; both have the specifications of hydraulically controlling the flow in advance and improving the performance within different driving status. Other more elaborate designs include Position Sensitive Damping (PSD) and Acceleration Sensitive Damping (ASD) that enhances Shock Absorber's capability in dealing with specific drive states; while technologies like the electrorheological and magnetorheological dampers make it possible to have the semi-active and adaptive suspension systems with optimum comfort and control.

In search of affordable OEM Honda Fit Shock Absorber? Consider browsing through our extensive inventory of genuine Honda Fit Shock Absorber. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Fit Shock Absorber Parts Questions & Experts Answers

Shock Absorber, Rear
52610-TK6-306
Q: How to remove the Rear Shock Absorber on a Honda Fit?
A: Loosen the rear wheel lug nuts. Raise the rear of the vehicle and support it securely on jackstands. Block the front wheels to prevent the vehicle from rolling. Remove the wheel. Support the rear axle beam with a floor jack placed under the coil spring pocket. Remove the access panel in the luggage compartment and unscrew the shock absorber upper mounting nut. Hold the shock absorber piston rod with an Allen wrench while loosening the upper mounting nut. Remove the washer and mounting cushion. Unscrew the shock absorber lower mounting bolt and nut and remove the shock absorber. Installation is the reverse of removal. Be sure the mounting cushions and upper washer are properly installed on the piston rod. Remove the plastic retainers and take off the steering column U-joint cover. Then tighten the NEW upper mounting nut to the torque. Raise the floor jack to simulate normal ride height, then tighten the NEW lower mounting bolt to the torque. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts to the torque.
Shock Absorber Assembly, Rear
52610-SLN-A04
Q: How Do I Replace a Strut and Coil Springs on a Honda Fit?
A: Remove the cowl cover, lower the cowl, and loosen the wheel lug nuts. Raise and support the vehicle, remove the wheels, and unplug the wheel speed sensor wiring along with the brake hose from the strut. Remove the wheel speed sensor from the steering knuckle, disconnect the stabilizer bar link from the strut, and remove strut-to-knuckle nuts and bolts. Separate the strut from the steering knuckle, hold the strut piston rod and remove the upper mounting nut and washer. Remove the damper mounting base and strut/spring assembly, and check the strut body and coil spring for damage. Place the strut cushion onto the strut and guide it into place. Install the mounting base, washer and nut, and raise the suspension with the jack. Tighten strut-to-knuckle bolts and nuts. Connect the stabilizer bar link and tighten the nut. Hold the strut piston rod and tighten the upper mounting nut, then put in the wheel and lug nuts, lower the vehicle, and tighten the lug nuts. Check and adjust the front-end alignment.
Shock Absorber Unit, Right Front
51605-SLN-A03
Q: How Should I Handle Strut or Coil Spring Wear on Honda Fit?
A: If signs of wear are present, check cost and availability of parts before disassembling. Remove strut and spring assembly, then mounting base. Install spring compressor and relieve pressure from upper spring seat. Remove piston rod nut and strut bearing. Inspect bearing for smooth operation. Replace rubber spring seat if necessary. Carefully lift compressed spring from assembly. Slide dust boot off piston rod. Check lower insulator for wear, cracking and hardness. Replace if necessary. For reassembly, set lower insulator into position. Extend damper rod and install dust boot. Place coil spring onto lower insulator. Install upper insulator and spring seat. Install upper spring seat and strut bearing. Install strut piston rod nut and tighten. Remove spring compressors. Install mounting base and strut coil spring assembly.

Related Honda Fit Parts

Browse by Year

2020 Shock Absorber 2019 Shock Absorber 2018 Shock Absorber 2017 Shock Absorber 2016 Shock Absorber 2015 Shock Absorber 2013 Shock Absorber 2012 Shock Absorber 2011 Shock Absorber 2010 Shock Absorber 2009 Shock Absorber 2008 Shock Absorber 2007 Shock Absorber