How do you remove and install the crankshaft front oil seal and Crankshaft Pulley on Honda CR-V?

First of all, pull the cable from the negative battery terminal also, and loosen the lugs nuts of the right-front wheel. Lift the car safely and place it on jackstands, now remove the right front wheel of the vehicle. Then, you are required to reach the splash shield beneath the engine compartment and then release the drivebelt. Loosen the crankshaft pulley bolt using a wrench that is made in such a way that it will not allow the crankshaft to turn; if one is not available, remove the flywheel/driveplate inspection cover and place a screwdriver horizontally between the starter ring gear teeth. Take the pulley with you and use the crankshaft front oil seal puller or(use a screwdriver that its tip is covered by tape so not to harm the crankshaft) Scrub the ID of the seal bore and inspect it for chips or slots and inspect the hub area for excessive or deep groove wearing or scoring and get a new hub if needed. When it is time to install I recommend that before installation you apply clean engine oil on the lip of the new seal, on the drive in the seal with a seal driver or a socket whose diameter is slightly smaller than the outside diameter of the seal that you are installing and to ensure it it is positioned correctly with the open side to the engine. Grease the sealing surface of the hub and put the crankshaft pulley on then tighten the bolt to the required torque. Last but not the least, perform the installation in the reverse order to the removal process and reconnect the battery.

Genuine Honda CR-V Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Crankshaft Seals found

View related parts
Honda CR-V Oil Seal (80X98X10) (Arai)
Part Number: 91214-RNB-A01
$12.92 MSRP: $18.25
You Save: $5.33 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PH7-004, 91214-PNA-014, 91214-PY3-003, 91214-RTA-004, 91214-PH7-003, 91214-PL2-004, 91214-PWA-003, 91214-PH7-013
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2006 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Oil Seal (43X58X7)
Part Number: 91212-R1B-A01
$5.49 MSRP: $7.75
You Save: $2.26 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal, Front Cover Seal, Oil Seal, Seal
- Replaces: 91212-RNA-A01, 91212-R40-A01, 91212-RTA-003, 91212-R11-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022 Honda CR-V | Hybrid EX, Hybrid EX-L, Hybrid Touring
- 2005-2014 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE, 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT, KA 5MT
View related parts
Honda CR-V Oil Seal (80X100X10) (Nok)
Part Number: 91214-PLE-003
$28.18 MSRP: $39.80
You Save: $11.62 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PH1-013, 91214-P2F-A01, 91214-PAA-A01, 91214-PH1-661, 91214-PLM-A01, 91214-PC7-003, 91214-PC6-003, 91214-PC6-013, 91214-PH3-751, 91214-P7A-004, 91214-PE1-721, 91214-PLC-003, 91214-PT0-004, 91214-PAA-A02, 91214-PD2-004, 91214-PLM-A02, 91214-PR4-A01, 91214-PLC-004, 91214-PH1-003, 91214-PH1-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda CR-V Oil Seal (43X58X7)
Part Number: 91212-59B-003
$19.07 MSRP: $26.93
You Save: $7.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2024 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, Hybrid Sport, Hybrid Sport Touring, Hybrid Sport-L, LX, Special Edition, Touring | KA CVT
View related parts
Honda CR-V Oil Seal (43X58X7) (Nok)
Part Number: 91212-PNC-003
$12.89 MSRP: $18.20
You Save: $5.31 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Cover Seal, Oil Seal, Seal
- Replaces: 91212-PNA-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda CR-V | 5 Door EX, 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Oil Seal (38X50X7.4)
Part Number: 91212-PR3-003
$14.05 MSRP: $19.86
You Save: $5.81 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Front Cover Seal
- Replaces: 91212-PR4-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda CR-V Oil Seal (80X98X10) (Arai)
Part Number: 91214-RZY-A01
$17.10 MSRP: $24.15
You Save: $7.05 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PWA-Y01, 91214-RZA-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2012 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Oil Seal (43X58X7) (Arai)
Part Number: 91212-PNC-004
$10.87 MSRP: $15.35
You Save: $4.48 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Oil Seal, Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda CR-V | 5 Door EX, 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Oil Seal (43X58X7) (Nok)
Part Number: 91212-RTA-003
$5.49 MSRP: $7.75
You Save: $2.26 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal
- Replaced by: 91212-R1B-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2012 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE, 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT, KA 5MT
View related parts
Honda CR-V Oil Seal (80X98X10)
Part Number: 91214-5A2-A01
$15.19 MSRP: $21.45
You Save: $6.26 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-RE0-H01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2019 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD) | KA CVT
View related parts
Honda CR-V Oil Seal (80X100X10) (Arai)
Part Number: 91214-P7A-004
$28.18 MSRP: $39.80
You Save: $11.62 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaced by: 91214-PLE-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda CR-V Oil Seal (80X98X10)
Part Number: 91214-R11-A01
$15.05 MSRP: $21.24
You Save: $6.19 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2014 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Oil Seal (43X58X7)
Part Number: 91212-5A2-A01
$22.15 MSRP: $31.28
You Save: $9.13 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD) | KA CVT
View related parts
Honda CR-V Oil Seal (80X98X10) (Arai)
Part Number: 91214-RZA-004
$17.10 MSRP: $24.15
You Save: $7.05 (30%)
ADD TO CART
Product Specifications
- Replaced by: 91214-RZY-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2012 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Oil Seal (43X58X7) (Arai)
Part Number: 91212-R40-A01
$5.49 MSRP: $7.75
You Save: $2.26 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal
- Replaced by: 91212-R1B-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2011 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Oil Seal,Low Torq
Part Number: 91214-59B-003
$13.12 MSRP: $18.53
You Save: $5.41 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2023 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, LX, Special Edition, Touring | KA CVT
View related parts
Honda CR-V Oil Seal,Low Torq
Part Number: 91212-5A2-A02
$9.56 MSRP: $13.49
You Save: $3.93 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD) | KA CVT
View related parts
Honda CR-V Oil Seal (80X98X10)
Part Number: 91214-6C1-A01
$15.88 MSRP: $22.43
You Save: $6.55 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022 Honda CR-V | Hybrid EX, Hybrid EX-L, Hybrid Touring
View related parts
Honda CR-V OIL SEAL (80X98X10)
Part Number: 91214-6C4-H01
$9.57 MSRP: $13.51
You Save: $3.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2023 Honda CR-V | Hybrid Sport, Hybrid Sport Touring

Honda CR-V Crankshaft Seal Parts Questions & Experts Answers

Oil Seal (80X98X10)
91214-R11-A01
Q: How do you remove and install the crankshaft front oil seal and Crankshaft Pulley on Honda CR-V?
A: First of all, pull the cable from the negative battery terminal also, and loosen the lugs nuts of the right-front wheel. Lift the car safely and place it on jackstands, now remove the right front wheel of the vehicle. Then, you are required to reach the splash shield beneath the engine compartment and then release the drivebelt. Loosen the crankshaft pulley bolt using a wrench that is made in such a way that it will not allow the crankshaft to turn; if one is not available, remove the flywheel/driveplate inspection cover and place a screwdriver horizontally between the starter ring gear teeth. Take the pulley with you and use the crankshaft front oil seal puller or(use a screwdriver that its tip is covered by tape so not to harm the crankshaft) Scrub the ID of the seal bore and inspect it for chips or slots and inspect the hub area for excessive or deep groove wearing or scoring and get a new hub if needed. When it is time to install I recommend that before installation you apply clean engine oil on the lip of the new seal, on the drive in the seal with a seal driver or a socket whose diameter is slightly smaller than the outside diameter of the seal that you are installing and to ensure it it is positioned correctly with the open side to the engine. Grease the sealing surface of the hub and put the crankshaft pulley on then tighten the bolt to the required torque. Last but not the least, perform the installation in the reverse order to the removal process and reconnect the battery.