How to disconnect the cable from the negative battery terminal and replace the Crankshaft Pulley on Honda CR-V?

Disconnect the cable from the negative battery terminal, loosen the right front wheel lug nuts, raise the vehicle, and support it securely on jackstands. Remove the wheel and the splash shield from below the engine compartment. Remove the drivebelt. Unscrew the crankshaft pulley bolt using a special tool that engages with the recessed hex in the pulley opening to prevent the crankshaft from turning; if unavailable, remove the flywheel/driveplate inspection cover and wedge a screwdriver into the starter ring gear teeth. Slip the pulley off the crankshaft, noting that the crankshaft pulley bolt can be incredibly tight, and an impact tool may be necessary if pulley holding tools are not used. Carefully pry the seal out of the housing with a seal removal tool or a screwdriver, ensuring not to nick or scratch the crankshaft or oil pump housing, as this could cause the new seal to leak. Clean the bore in the seal housing and coat the outer edge of the new seal with engine oil or multi-purpose grease. Using a seal driver or a socket with an outside diameter slightly smaller than the seal, carefully drive the seal into place with a hammer until the inner edge is 7/32 to 15/64-inch deep, checking afterward to ensure the spring did not pop out. Lubricate the lip of the seal with a thin film of engine oil or multi-purpose grease, then lubricate the crankshaft bolt with oil between the head of the bolt and the washer and the first few threads of the oil only before installing the crankshaft pulley, ensuring the flats on the sleeve align with the inner oil pump gear. Complete the installation in reverse order and run the engine to check for leaks.

Genuine Honda CR-V Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Crankshaft Pulleys found

View related parts
Honda CR-V Pulley, Crankshaft
Part Number: 13810-RRA-A02
$95.86 MSRP: $135.40
You Save: $39.54 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Replaces: 13810-PNL-E01, 13810-PNA-003, 13810-RRA-A01, 13810-PNA-013, 13810-RAA-A01, 13810-RAA-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2006 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Pulley, Crankshaft
Part Number: 13810-R40-A01
$182.05 MSRP: $259.34
You Save: $77.29 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Replaces: 13810-R40-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2014 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Pulley, Crankshaft
Part Number: 13810-RZA-A01
$144.90 MSRP: $206.41
You Save: $61.51 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Replaces: 13810-RZA-008
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2009 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door LX (2WD), 5 Door LX (4WD) | KA 5AT
View related parts
Honda CR-V Pulley Complete Crank
Part Number: 13810-59B-003
$262.37 MSRP: $373.75
You Save: $111.38 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2022 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, LX, Special Edition, Touring | KA CVT
View related parts
Honda CR-V Pulley, Crankshaft
Part Number: 13810-R40-A02
$182.05 MSRP: $259.34
You Save: $77.29 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Replaced by: 13810-R40-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2012 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Pulley, Complete Crank
Part Number: 13810-5A2-A01
$115.10 MSRP: $162.57
You Save: $47.47 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2019 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD) | KA CVT
View related parts
Honda CR-V Damper, Crankshaft
Part Number: 13810-6C1-A01
$141.16 MSRP: $201.08
You Save: $59.92 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022 Honda CR-V | Hybrid EX, Hybrid EX-L, Hybrid Touring
View related parts
Honda CR-V PULLEY COMP
Part Number: 13810-64A-A01
$164.41 MSRP: $234.20
You Save: $69.79 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Pulley
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2023-2024 Honda CR-V | EX, EX-L, LX
View related parts
Honda CR-V DAMPER, CRANKSHAFT
Part Number: 13810-6MA-J01
$30.05 MSRP: $42.44
You Save: $12.39 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2023-2024 Honda CR-V | Hybrid Sport, Hybrid Sport Touring, Hybrid Sport-L
View related parts
Honda CR-V Pulley, Crankshaft
Part Number: 13810-P3F-003
Product Specifications
- Other Name: Crankshaft Pulley; Pulley
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda CR-V Crankshaft Pulley

Used in Honda CR-V cars, the Performance Crankshaft Pulley plays a great part in transmitting torque from the engines to the parts including the power steering pump, the A/C compressor, and Alternator. Being directly coupled to the crankshaft, the Performance Crankshaft Pulley allows to run torque without absorbing vibrations, which adds an alternate name to this component - harmonic balance wheel. There are many Performance Crankshaft Pulley designs out there that have been used in CR V series Hondas over the years, all of which had one goal in mind, to improve performance and efficiency. These pulleys may also be made of different material and structure in such a way that they affect the weight per unit length of Mechatronics and their vibration isolation properties.

In search of affordable OEM Honda CR-V Crankshaft Pulley? Consider browsing through our extensive inventory of genuine Honda CR-V Crankshaft Pulley. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda CR-V Crankshaft Pulley Parts Questions & Experts Answers

Pulley, Crankshaft
13810-R40-A01
Q: How to disconnect the cable from the negative battery terminal and replace the Crankshaft Pulley on Honda CR-V?
A: Disconnect the cable from the negative battery terminal, loosen the right front wheel lug nuts, raise the vehicle, and support it securely on jackstands. Remove the wheel and the splash shield from below the engine compartment. Remove the drivebelt. Unscrew the crankshaft pulley bolt using a special tool that engages with the recessed hex in the pulley opening to prevent the crankshaft from turning; if unavailable, remove the flywheel/driveplate inspection cover and wedge a screwdriver into the starter ring gear teeth. Slip the pulley off the crankshaft, noting that the crankshaft pulley bolt can be incredibly tight, and an impact tool may be necessary if pulley holding tools are not used. Carefully pry the seal out of the housing with a seal removal tool or a screwdriver, ensuring not to nick or scratch the crankshaft or oil pump housing, as this could cause the new seal to leak. Clean the bore in the seal housing and coat the outer edge of the new seal with engine oil or multi-purpose grease. Using a seal driver or a socket with an outside diameter slightly smaller than the seal, carefully drive the seal into place with a hammer until the inner edge is 7/32 to 15/64-inch deep, checking afterward to ensure the spring did not pop out. Lubricate the lip of the seal with a thin film of engine oil or multi-purpose grease, then lubricate the crankshaft bolt with oil between the head of the bolt and the washer and the first few threads of the oil only before installing the crankshaft pulley, ensuring the flats on the sleeve align with the inner oil pump gear. Complete the installation in reverse order and run the engine to check for leaks.