How to remove and install Ignition Lock Cylinder on Honda Prelude?

Models with a Supplemental Restraint System (SRS) that contain an air bag pose some risk when operating around air bag installation components such as impact sensors, air bag module, steering column and instrument panel and therefore necessitate the disabling of the SRS. It involves initial steps of electrical interference, that is, cutting off the supply of electricity to the air bag system and using a wrench to remove the car's negative terminal from the battery. Steering column is detached by way of withdrawing the steering wheel, the driver's side dash lower, and knee bolster and finally the steering column. Should the car have an automatic transaxle, set the gear selector to neutral and remove the selector cable. Secondly, if fitted, then disconnect the combination switches from the steering column, check the matchmark and disconnect the steering joint in the engine bay, also, take out the fasteners anchoring the steering column. Disconnect the wiring harness from lower dash cover, then pull the steering column housing down. While removing the shear bolt(s), centre punch the shear bolt(s) and then drill out the head(s) with a 3/16 inch (5mm) drill. Place the ignition key and turn the Turn the ignition switch to position it at 'I' then you press down the lock pin situated at the service hole of the clamp to try and unlock the lock assembly from the column. For installation, turn the ignition switch to the 'I' again while inserting the key then press the lock key downwards and fix the lock assembly to the column. Installing the lock body may require you to do this without the key to enable fitment to be carried out to perfection. Tighten the new shear bolts only with fingers, turn the key into new lock cylinder, and ensure appropriate performance of the switches. Close the shear bolt(s) by spinning the nuts until the heads are flush with the bolt-they should be accessible for removal only; adjust the steering column and fasten bolts. Connect the harness after to the ignition switch, put on the steering column covers, the dashboard panel, and knee bolster, then reconnect the negative terminal of battery and turn on the air bag by last.

Genuine Honda Prelude Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Ignition Lock Cylinders found

View related parts
Honda Prelude Key Set, Cylinder (Service)
Part Number: 06350-SS0-A10
$402.21 MSRP: $580.38
You Save: $178.17 (31%)
ADD TO CART
Product Specifications
- Replaced by: 06350-SS0-A12
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1994-1996 Honda Prelude | 2 Door SI | KA 4AT, KL 4AT
View related parts
Honda Prelude Key Set, Cylinder (Service)
Part Number: 06350-SS0-A20
$420.89 MSRP: $607.35
You Save: $186.46 (31%)
ADD TO CART
Product Specifications
- Replaced by: 06350-SS0-A22
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1994-1996 Honda Prelude | 2 Door S | KA 5MT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SB0-677
$179.84 MSRP: $256.18
You Save: $76.34 (30%)
ADD TO CART
Product Specifications
- Other Name: Ignition Lock Cylinder; Ignition Lock, Ignition Switch
- Replaces: 35100-SB0-674, 35100-SB0-673
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985 Honda Prelude | 2 Door DX | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Key Set, Cylinder (Service)
Part Number: 06350-SS0-A00
$347.29 MSRP: $494.72
You Save: $147.43 (30%)
ADD TO CART
Product Specifications
- Replaced by: 06350-SS0-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1994-1996 Honda Prelude | 2 Door SI, 2 Door Sivtec | KA 5MT, KL 5MT
View related parts
Honda Prelude Cylinder Set, Key (Service)
Part Number: 06350-SS0-A30
$362.42 MSRP: $516.28
You Save: $153.86 (30%)
ADD TO CART
Product Specifications
- Replaced by: 06350-SS0-A32
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1994-1996 Honda Prelude | 2 Door S | KA 4AT, KL 4AT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-S30-A12
Product Specifications
- Replaced by: 35100-S30-A13
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-1999 Honda Prelude | 2 Door Base | KA 4AT
View related parts
Honda Prelude Cylinder, Steering
Part Number: 35131-SB0-671
Product Specifications
- Other Name: Ignition Lock Cylinder; Cylinder & Key
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985-1991 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0S, 2 Door 2.0SI, 2 Door DX, 2 Door SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SF1-A01
Product Specifications
- Other Name: Switch & Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1991 Honda Prelude | 2 Door 2.0S, 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SF1-A11
Product Specifications
- Other Name: Switch & Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1990-1991 Honda Prelude | 2 Door 2.0S, 2 Door 2.0SI | KA 4AT, KL 4AT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SF1-A81
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1990-1991 Honda Prelude | 2 Door 2.05SI | KA 4AT, KL 4AT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SF1-A91
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1991 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SB0-672
Product Specifications
- Other Name: Ignition Lock Cylinder; Ignition Switch
- Replaces: 35100-SB0-671
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1983-1984 Honda Prelude | 2 Door DX | KA 4AT, KA 5MT, KH 4AT, KH 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SB0-676
Product Specifications
- Replaced by: 35100-SB0-678
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985-1987 Honda Prelude | 2 Door DX, 2 Door SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Set, Cylinder
Part Number: 35010-SB0-675ZZ
Product Specifications
- Replaced by: 35020-SB0-670
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985-1986 Honda Prelude | 2 Door DX, 2 Door SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-692-671
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-692-681
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1980 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SA0-674
Product Specifications
- Replaces: 35100-SA0-671, 35100-SA0-673
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1981-1982 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SS0-A11
Product Specifications
- Other Name: Ignition Lock Cylinder; Steering Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1996 Honda Prelude | 2 Door SI | KA 4AT, KL 4AT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SS0-A01
Product Specifications
- Other Name: Ignition Lock Cylinder; Steering Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1996 Honda Prelude | 2 Door SI, 2 Door Sivtec | KA 5MT, KL 5MT
View related parts
Honda Prelude Lock Assy., Steering
Part Number: 35100-SS0-A21
Product Specifications
- Other Name: Ignition Lock Cylinder; Steering Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1996 Honda Prelude | 2 Door S | KA 5MT, KL 5MT

| Page 1 of 3 |Next >

1-20 of 42 Results

Honda Prelude Ignition Lock Cylinder

The Ignition Lock Cylinder in Honda automobiles particularly in Prelude type of automobiles is mainly used to start the engine by inserting and turning a key. It is an element of the ignition switch through which battery power is provided to the circuits within a car whenever the appropriate key is inserted. The Honda Prelude ignition lock cylinder has undergone changes in the years by having keys stuck into the ignition lock cylinder for starting the car in older models while newer models contain coded key-for-car computers that basically do not allow the car to start if someone else has the keys. However, the Honda Prelude ignition lock cylinder like all other parts is venerable to wear and Malfunction the lock cylinder could get harms and the key may not turn or start the engine as required. Problems can be caused by worn keys or tumblers, or have their source in the defects of the switch itself.

In search of affordable OEM Honda Prelude Ignition Lock Cylinder? Consider browsing through our extensive inventory of genuine Honda Prelude Ignition Lock Cylinder. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Prelude Ignition Lock Cylinder Parts Questions & Experts Answers

Lock Assy., Steering
35100-S30-A12
Q: How to remove and install Ignition Lock Cylinder on Honda Prelude?
A: Models with a Supplemental Restraint System (SRS) that contain an air bag pose some risk when operating around air bag installation components such as impact sensors, air bag module, steering column and instrument panel and therefore necessitate the disabling of the SRS. It involves initial steps of electrical interference, that is, cutting off the supply of electricity to the air bag system and using a wrench to remove the car's negative terminal from the battery. Steering column is detached by way of withdrawing the Steering Wheel, the driver's side dash lower, and knee bolster and finally the steering column. Should the car have an automatic transaxle, set the gear selector to neutral and remove the selector cable. Secondly, if fitted, then disconnect the combination switches from the steering column, check the matchmark and disconnect the steering joint in the engine bay, also, take out the fasteners anchoring the steering column. Disconnect the wiring harness from lower dash cover, then pull the steering column housing down. While removing the shear bolt(s), centre punch the shear bolt(s) and then drill out the head(s) with a 3/16 inch (5mm) drill. Place the ignition key and turn the Turn the Ignition Switch to position it at 'I' then you press down the lock pin situated at the service hole of the clamp to try and unlock the lock assembly from the column. For installation, turn the ignition switch to the 'I' again while inserting the key then press the lock key downwards and fix the lock assembly to the column. Installing the lock body may require you to do this without the key to enable fitment to be carried out to perfection. Tighten the new shear bolts only with fingers, turn the key into new lock cylinder, and ensure appropriate performance of the switches. Close the shear bolt(s) by spinning the nuts until the heads are flush with the bolt-they should be accessible for removal only; adjust the steering column and fasten bolts. Connect the harness after to the ignition switch, put on the steering column covers, the dashboard panel, and knee bolster, then reconnect the negative terminal of battery and turn on the air bag by last.