How to remove and install a distributor cap and Rotor for the Honda Prelude?

Before you take off the distributor cap, make sure to mark the positions of the wires. Unscrew the bolts that hold the cap and then pull out the rotor. Record down your radios security code as you disconnect the battery. Remove ignition wires from both the cap and distributor cap itself. You should look for any damage on the seal or cap. Now place that rotor into its shaft and put back that cap in its housing. Tighten them using a crisscross pattern of fasteners. Then, reattach wires and batteries and punch in radio code numbers too. Replace them if they are cracked or their electrodes are worn out and clean before reinstalling them.

Genuine Honda Prelude Distributor Rotor

Ignition Distributor Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Distributor Rotors found

View related parts
Honda Prelude Head Assy., Rotor
Part Number: 30103-P08-003
$31.12 MSRP: $43.95
You Save: $12.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Rotor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-2001 Honda Prelude | 2 Door Base, 2 Door S, 2 Door SI, 2 Door Sivtec, 2 Door TYPESH | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-634-005
$6.30 MSRP: $8.91
You Save: $2.61 (30%)
ADD TO CART
Product Specifications
- Replaced by: 30103-PA5-005
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PA1-732
Product Specifications
- Replaced by: 30103-PE9-006
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PA1-733
Product Specifications
- Replaced by: 30103-PE9-006
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Rotor, Distributor
Part Number: 30103-PA5-005
Product Specifications
- Other Name: Rotor
- Replaces: 30103-PA0-005, 30103-PB9-601, 30103-634-005, 30103-PC2-661
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1990 Honda Prelude | 2 Door **, 2 Door 2.0S, 2 Door DX | KA 4AT, KA 5MT, KA HMT, KH 4AT, KH 5MT, KH HMT, KL 4AT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PC3-822
Product Specifications
- Replaced by: 30103-PE9-006
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982-1990 Honda Prelude | 2 Door **, 2 Door 2.0S, 2 Door DX, 2 Door SI | KA 4AT, KA 5MT, KA HMT, KH 4AT, KH 5MT, KH HMT, KL 4AT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PA0-005
Product Specifications
- Replaced by: 30103-PA5-005
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1981 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PB9-601
Product Specifications
- Replaced by: 30103-PA5-005
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1982 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Head, Rotor
Part Number: 30103-PK2-006
Product Specifications
- Other Name: Rotor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1991 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda Prelude Distributor Rotor

The Distributor Rotor in Honda Prelude cars is an important part in the operation of the ignition system; it is responsible for delivering high voltage from the ignition coil to the engine's cylinders in the right moment. Being rotatable, this part situated in the distributor cap and moving in phase with the camshaft, is responsible for the proper running of the engine since it ignites the air-fuel mixture located in the combustion chamber. Distributor Rotors that have been used in different organizations of the Prelude model consist of; some types are driven using a gear that is on the camshaft in overhead valve engines and others which are attached to the camshaft in overhead camshaft engines. It is advisable to timely inspect the entire Ignition System as well as the Distributor Rotor as problems with them can result to things like a complete engine malfunction or the car not starting in the first instance.

In search of affordable OEM Honda Prelude Distributor Rotor? Consider browsing through our extensive inventory of genuine Honda Prelude Distributor Rotor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Prelude Distributor Rotor Parts Questions & Experts Answers

Head Assy., Rotor
30103-P08-003
Q: How to remove and install a distributor cap and Rotor for the Honda Prelude?
A: Before you take off the distributor cap, make sure to mark the positions of the wires. Unscrew the bolts that hold the cap and then pull out the rotor. Record down your radios security code as you disconnect the battery. Remove ignition wires from both the cap and distributor cap itself. You should look for any damage on the seal or cap. Now place that rotor into its shaft and put back that cap in its housing. Tighten them using a crisscross pattern of fasteners. Then, reattach wires and batteries and punch in radio code numbers too. Replace them if they are cracked or their electrodes are worn out and clean before reinstalling them.