How do you properly remove and replace the stabilizer bar and Bushing on Honda Odyssey?

First, remove the front wheel lug nuts, next, jack up the front of the bicycle and place it on two jackstands. The use of the parking brake should be accompanied by a blocking of the rear wheels so that the vehicle cannot move. Take off the front wheels, then the nuts of the sway bar bushing retainers and take the retainers off the bushings, using a pry bar if required. Then, first take out the nuts that fasten the upper and lower ends of the sway bar links to the strut/coil spring assembly and the sway bar kit; for this, while turning the nut, it is helpful to hold the stud in place with an Allen wrench, then take off the links. Check the shape of the retainer bushings: if they are cracked or torn-replace both of them; if the ballstuds on the links are loose or worn-replace the links too. Place the links on to the requested locations and then turn the nuts of the links until you obtain the required torque. After removing the old retainer bushings, take time and clean the areas on the sway bar where the new retainer bushings will be installed, before lubricating both the inside and outside of the bushings with vegetable oil to ease reassembly, this should be done in a way that the slit in each of the bushings lies in the forward direction. Bolt and fit the retainers firmly with the specified torque level of the bolts. Last but not the least, fit the wheels and the lug nuts, lift the car and then finally tighten the lug nuts to the requisite torque. Regard to the sway bar removal it entails lowering the subframe and the removal of the sway bar when the subframe is out of the vehicle ordinarily requires professional help if the damage arises from severe accidents.

Genuine Honda Odyssey Sway Bar Bushing

Stabilizer Sway Bar Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Sway Bar Bushings found

View related parts
Honda Odyssey Bush, Stabilizer Holder
Part Number: 51306-STX-A12
$6.15 MSRP: $8.68
You Save: $2.53 (30%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Mount Bushing; Bushing, Stabilizer Bar Bushing
- Replaces: 51306-STX-A11, 51306-SHJ-A61
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door Touring | KA 5AT, KA 6AT
- 2005-2009 Honda Odyssey | 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Bush, Stabilizer Holder
Part Number: 51306-S3V-A00
$9.55 MSRP: $13.48
You Save: $3.93 (30%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Mount Bushing; Bushing, Stabilizer Bar Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Bush
Part Number: 51306-TK8-A01
$6.86 MSRP: $9.69
You Save: $2.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Bushing; Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Touring | KA 6AT
View related parts
Honda Odyssey Bush, Front Stabilizer Holder
Part Number: 51306-THR-A52
$6.86 MSRP: $9.69
You Save: $2.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Position: Front
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door Touring (10AT), EX-L, Elite, Touring | KA 9AT, KA XAT
View related parts
Honda Odyssey Bush, Stabilizer End
Part Number: 52316-SA5-000
$2.66 MSRP: $3.74
You Save: $1.08 (29%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Outer Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Honda Odyssey | 5 Door EX, 5 Door LX (6 Seats), 5 Door LX (7 Seats) | KA 4AT
View related parts
Honda Odyssey Bush, Stabilizer Holder (22MM)
Part Number: 51306-S0X-A02
$5.57 MSRP: $7.86
You Save: $2.29 (30%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Mount Bushing; Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door VAN | KA 5AT
View related parts
Honda Odyssey Bush, Stabilizer Holder (24MM)
Part Number: 51306-S0X-A01
$8.07 MSRP: $11.40
You Save: $3.33 (30%)
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar Mount Bushing; Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1999-2001 Honda Odyssey | 5 Door EX, 5 Door LX, 5 Door VAN | KA 4AT
View related parts
Honda Odyssey Bush, Rear Stabilizer Holder
Part Number: 52306-THR-A01
$6.86 MSRP: $9.69
You Save: $2.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), 5 Door EX, 5 Door EX (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door LX, 5 Door LX (10AT), 5 Door Touring (10AT), EX, EX-L, Elite, Sport, Touring | KA 9AT, KA XAT
View related parts
Honda Odyssey Bush, Front Stabilizer Holder
Part Number: 51306-THR-A02
$6.86 MSRP: $9.69
You Save: $2.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Bushing, Stabilizer Bar Bushing
- Position: Front
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door EX, 5 Door EX (10AT), 5 Door LX, 5 Door LX (10AT), EX | KA 9AT, KA XAT
View related parts
Honda Odyssey Bush, Rear Stabilizer (13.0)
Part Number: 52315-SK7-900
Product Specifications
- Other Name: Stabilizer Bar Bushing; Bushing
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Honda Odyssey | 5 Door EX, 5 Door LX (6 Seats), 5 Door LX (7 Seats) | KA 4AT
View related parts
Honda Odyssey Bush, Stabilizer Holder (30.0MM)
Part Number: 51306-SX0-003
Product Specifications
- Other Name: Stabilizer Bar Mount Bushing; Bushing
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Honda Odyssey | 5 Door EX, 5 Door LX (6 Seats), 5 Door LX (7 Seats) | KA 4AT

Honda Odyssey Sway Bar Bushing Parts Questions & Experts Answers

Bush, Stabilizer Holder (22MM)
51306-S0X-A02
Q: How do you properly remove and replace the stabilizer bar and Bushing on Honda Odyssey?
A: First, remove the front wheel lug nuts, next, jack up the front of the bicycle and place it on two jackstands. The use of the parking brake should be accompanied by a blocking of the rear wheels so that the vehicle cannot move. Take off the front wheels, then the nuts of the sway bar bushing retainers and take the retainers off the bushings, using a pry bar if required. Then, first take out the nuts that fasten the upper and lower ends of the sway bar links to the strut/coil spring assembly and the sway bar kit; for this, while turning the nut, it is helpful to hold the stud in place with an Allen wrench, then take off the links. Check the shape of the retainer bushings: if they are cracked or torn-replace both of them; if the ballstuds on the links are loose or worn-replace the links too. Place the links on to the requested locations and then turn the nuts of the links until you obtain the required torque. After removing the old retainer bushings, take time and clean the areas on the sway bar where the new retainer bushings will be installed, before lubricating both the inside and outside of the bushings with vegetable oil to ease reassembly, this should be done in a way that the slit in each of the bushings lies in the forward direction. Bolt and fit the retainers firmly with the specified torque level of the bolts. Last but not the least, fit the wheels and the lug nuts, lift the car and then finally tighten the lug nuts to the requisite torque. Regard to the sway bar removal it entails lowering the subframe and the removal of the sway bar when the subframe is out of the vehicle ordinarily requires professional help if the damage arises from severe accidents.