How do you remove and install the crankshaft front oil seal and Crankshaft Pulley on Honda Civic?

First of all, pull the cable from the negative battery terminal also, and loosen the lugs nuts of the right-front wheel. Lift the car safely and place it on jackstands, now remove the right front wheel of the vehicle. Then, you are required to reach the splash shield beneath the engine compartment and then release the drivebelt. Loosen the crankshaft pulley bolt using a wrench that is made in such a way that it will not allow the crankshaft to turn; if one is not available, remove the flywheel/driveplate inspection cover and place a screwdriver horizontally between the starter ring gear teeth. Take the pulley with you and use the crankshaft front oil seal puller or(use a screwdriver that its tip is covered by tape so not to harm the crankshaft) Scrub the ID of the seal bore and inspect it for chips or slots and inspect the hub area for excessive or deep groove wearing or scoring and get a new hub if needed. When it is time to install I recommend that before installation you apply clean engine oil on the lip of the new seal, on the drive in the seal with a seal driver or a socket whose diameter is slightly smaller than the outside diameter of the seal that you are installing and to ensure it it is positioned correctly with the open side to the engine. Grease the sealing surface of the hub and put the crankshaft pulley on then tighten the bolt to the required torque. Last but not the least, perform the installation in the reverse order to the removal process and reconnect the battery.

Genuine Honda Civic Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Crankshaft Seals found

View related parts
Honda Civic Oil Seal (31X46X8)
Part Number: 91212-PE0-662
$8.78 MSRP: $16.97
You Save: $8.19 (49%)
ADD TO CART
Product Specifications
- Replaces: 91212-PE0-661, 91212-PG7-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1986-1991 Honda Civic | 3 Door (1300), 3 Door DX, 3 Door SI, 4 Door DX, 4 Door EX, 4 Door GL, 4 Door LX, 5 Door (Wagovan), 5 Door 4WD, 5 Door DX, 5 Door WV | KA 4AT, KA 4MT, KA 5MT, KH 4MT, KL 4AT, KL 4MT, KL 5MT
View related parts
Honda Civic Oil Seal (80X98X10) (Arai)
Part Number: 91214-RNB-A01
$12.81 MSRP: $18.25
You Save: $5.44 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PH7-004, 91214-PNA-014, 91214-PY3-003, 91214-RTA-004, 91214-PH7-003, 91214-PL2-004, 91214-PWA-003, 91214-PH7-013
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2015 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 3 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door HF, 4 Door LX, 4 Door LX (AT), 4 Door LX-S, 4 Door MX (Hybrid) | KA 5AT, KA 5MT, KA 6MT, KA CVT, KL 5AT, KL 5MT, KL CVT
View related parts
Honda Civic Oil Seal (43X58X7)
Part Number: 91212-R1B-A01
$5.58 MSRP: $7.95
You Save: $2.37 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal, Front Cover Seal, Oil Seal, Seal
- Replaces: 91212-RNA-A01, 91212-R40-A01, 91212-RTA-003, 91212-R11-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2015 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door HF, 4 Door LX, 4 Door LX (AT), 4 Door LX-S, 4 Door SI | KA 5AT, KA 5MT, KA 6MT, KA CVT, KL 5AT, KL CVT
View related parts
Honda Civic Oil Seal (80X100X10) (Nok)
Part Number: 91214-PLE-003
$28.67 MSRP: $40.83
You Save: $12.16 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PH1-013, 91214-P2F-A01, 91214-PAA-A01, 91214-PH1-661, 91214-PLM-A01, 91214-PC7-003, 91214-PC6-003, 91214-PC6-013, 91214-PH3-751, 91214-P7A-004, 91214-PE1-721, 91214-PLC-003, 91214-PT0-004, 91214-PAA-A02, 91214-PD2-004, 91214-PLM-A02, 91214-PR4-A01, 91214-PLC-004, 91214-PH1-003, 91214-PH1-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1984-2005 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-S, 2 Door HX, 2 Door LX, 2 Door SI, 3 Door (1300), 3 Door CX, 3 Door DX, 3 Door S, 3 Door SI, 3 Door STD, 3 Door VX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GL, 4 Door GX, 4 Door LX, 4 Door LX-CAR, 5 Door (Wagovan), 5 Door 4WD, 5 Door DX, 5 Door WV | KA 3AT, KA 4AT, KA 4MT, KA 5MT, KA CVT, KH 4MT, KL 3AT, KL 4AT, KL 4MT, KL 5MT, KL CVT, KR 5MT, KW 5MT
View related parts
Honda Civic Oil Seal (43X58X7)
Part Number: 91212-59B-003
$19.56 MSRP: $27.63
You Save: $8.07 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2023 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 2 Door SI, 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-A, 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE, 4 Door SI, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo), 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Sport, 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring), EX, EX-L, LX, Si, Sport, Sport Touring, Touring, Type R | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Oil Seal (43X58X7) (Nok)
Part Number: 91212-PNC-003
$13.22 MSRP: $18.67
You Save: $5.45 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Cover Seal, Oil Seal, Seal
- Replaces: 91212-PNA-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda Civic | 3 Door SI | KA 5MT
View related parts
Honda Civic Oil Seal (38X50X7.4)
Part Number: 91212-PR3-003
$14.42 MSRP: $20.37
You Save: $5.95 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Front Cover Seal
- Replaces: 91212-PR4-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1999-2000 Honda Civic | 2 Door SI | KA 5MT
View related parts
Honda Civic Oil Seal (31X46X7)
Part Number: 91212-P2F-A01
$6.16 MSRP: $8.70
You Save: $2.54 (30%)
ADD TO CART
Product Specifications
- Replaces: 91212-P06-A01, 91212-P7A-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-2000 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-S, 2 Door HX, 3 Door CX, 3 Door DX, 3 Door SI, 3 Door VX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX | KA 4AT, KA 5MT, KA CVT, KL 4AT, KL 5MT, KL CVT, KR 5MT, KW 5MT
View related parts
Honda Civic Oil Seal (38X50X7) (Yamada)
Part Number: 91212-PLM-A01
$6.56 MSRP: $9.35
You Save: $2.79 (30%)
ADD TO CART
Product Specifications
- Other Name: Oil Seal
- Replaces: 91212-PLC-004, 91212-PLC-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2000-2005 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door LX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX, 4 Door LX-CAR | KA 4AT, KA 5MT, KA CVT, KL 4AT, KL 5MT, KL CVT
View related parts
Honda Civic Oil Seal (80X98X10) (Arai)
Part Number: 91214-RZY-A01
$17.55 MSRP: $24.78
You Save: $7.23 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PWA-Y01, 91214-RZA-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2011 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic Oil Seal (43X58X7) (Arai)
Part Number: 91212-PNC-004
$10.87 MSRP: $15.35
You Save: $4.48 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Oil Seal, Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda Civic | 3 Door SI | KA 5MT
View related parts
Honda Civic Oil Seal (43X58X7) (Nok)
Part Number: 91212-RTA-003
$5.58 MSRP: $7.95
You Save: $2.37 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal
- Replaced by: 91212-R1B-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2015 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door HF, 4 Door LX, 4 Door LX (AT), 4 Door LX-S, 4 Door SI | KA 5AT, KA 5MT, KA 6MT, KA CVT, KL 5AT, KL CVT
View related parts
Honda Civic Oil Seal (80X98X10)
Part Number: 91214-5A2-A01
$15.58 MSRP: $22.01
You Save: $6.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-RE0-H01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2023 Honda Civic | 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 4 Door EX, 4 Door EX-A, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring), LX, Sport, Type R | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Oil Seal (40X55X7) (Nok)
Part Number: 91212-PWA-003
$10.87 MSRP: $15.35
You Save: $4.48 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Crankshaft Seal, Front Seal, Oil Seal
- Replaces: 91202-PHM-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2011 Honda Civic | 4 Door MX (Hybrid) | KA 5MT, KA CVT, KL 5MT, KL CVT
View related parts
Honda Civic Oil Seal (80X100X10) (Arai)
Part Number: 91214-P7A-004
$28.67 MSRP: $40.83
You Save: $12.16 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaced by: 91214-PLE-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996-2005 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door LX, 3 Door CX, 3 Door DX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX, 4 Door LX-CAR | KA 4AT, KA 5MT, KA CVT, KL 4AT, KL 5MT, KL CVT, KR 5MT, KW 5MT
View related parts
Honda Civic Oil Seal (80X98X10)
Part Number: 91214-R11-A01
$15.43 MSRP: $21.80
You Save: $6.37 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2015 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic Oil Seal (80X100X10) (Nok)
Part Number: 91214-PAA-A01
$28.67 MSRP: $40.83
You Save: $12.16 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaced by: 91214-PLE-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2000 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 3 Door CX, 3 Door DX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX | KA 4AT, KA 5MT, KA CVT, KL 4AT, KL 5MT, KL CVT, KW 5MT
View related parts
Honda Civic Oil Seal (80X98X10) (Nok)
Part Number: 91214-RB0-003
$24.91 MSRP: $35.48
You Save: $10.57 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2015 Honda Civic | 4 Door MX, 4 Door MX (Hybrid) | KA CVT, KL CVT
View related parts
Honda Civic Oil Seal (40X55X7) (Nok)
Part Number: 91212-RB0-003
$12.99 MSRP: $18.50
You Save: $5.51 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2015 Honda Civic | 4 Door MX, 4 Door MX (Hybrid) | KA CVT, KL CVT
View related parts
Honda Civic Oil Seal,Low Torq
Part Number: 91214-59B-003
$13.46 MSRP: $19.02
You Save: $5.56 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2023 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door SI, 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door SI, 4 Door Touring, 4 Door Touring (Turbo), 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Sport, EX, EX-L, Si, Sport Touring, Touring | KA 6MT, KA CVT, KL CVT

| Page 1 of 2 |Next >

1-20 of 30 Results

Honda Civic Crankshaft Seal

This part known as the Crankshaft Seal is situated at the front of an engine in Honda Civic cars and its function is to avoid the exudation of oil from the crankcase. Usually, it is made of metal-rubber compound, this round seal is vital since it helps in the circulation of lubricant around the engine to help decrease the friction and protect the parts from wear. There are many types of Crankshaft Seal that has been fitted into Honda Civic since related year, however, the function is still alike. If the Crankshaft Seal is worn or damaged then you can observe oil leakage particularly in cars with high kilometers done on the car hence the need for replacement. Diagnosing the signs of a faulty Crankshaft Seal to help in preventing poor efficiency and longevity of the Honda Civics.

In search of affordable OEM Honda Civic Crankshaft Seal? Consider browsing through our extensive inventory of genuine Honda Civic Crankshaft Seal. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Civic Crankshaft Seal Parts Questions & Experts Answers

Oil Seal (43X58X7)
91212-R1B-A01
Q: How do you remove and install the crankshaft front oil seal and Crankshaft Pulley on Honda Civic?
A: First of all, pull the cable from the negative battery terminal also, and loosen the lugs nuts of the right-front wheel. Lift the car safely and place it on jackstands, now remove the right front wheel of the vehicle. Then, you are required to reach the splash shield beneath the engine compartment and then release the drivebelt. Loosen the crankshaft pulley bolt using a wrench that is made in such a way that it will not allow the crankshaft to turn; if one is not available, remove the flywheel/driveplate inspection cover and place a screwdriver horizontally between the starter ring gear teeth. Take the pulley with you and use the crankshaft front oil seal puller or(use a screwdriver that its tip is covered by tape so not to harm the crankshaft) Scrub the ID of the seal bore and inspect it for chips or slots and inspect the hub area for excessive or deep groove wearing or scoring and get a new hub if needed. When it is time to install I recommend that before installation you apply clean engine oil on the lip of the new seal, on the drive in the seal with a seal driver or a socket whose diameter is slightly smaller than the outside diameter of the seal that you are installing and to ensure it it is positioned correctly with the open side to the engine. Grease the sealing surface of the hub and put the crankshaft pulley on then tighten the bolt to the required torque. Last but not the least, perform the installation in the reverse order to the removal process and reconnect the battery.