What steps must be taken before removing the piston and connecting rod assemblies on Honda Accord?

Before the assemblies of pistons and connecting rods can be dismantled the cylinder head and oil pan have to be disconnected. First, look that whether there is ridge formation at the upper limit of ring travel in each cylinder, if so than this must be done by ridge reamer for avoiding piston breakage. Once the ridges are turned to the top turn the engine onto its side so the crankshaft is now at the top. After that, the connecting rod end-play has to be measured with the help of feeler gauges; it has to be within a given range; if it goes beyond this range, new connecting rods may be required. It is recommended to mark the connecting rods and caps to distinguish them before removing the connecting rod cap bolts and the cap itself, during which you should look for any traces of damage. Extract the connecting rod and piston assembly through the top of the engine and perform the same on all the cylinders. After removal, screw the connecting rod caps and setting geographical bearing inserts back into position and retain the old inserts especially for protection of surfaces. For piston ring installation, check the value of ring end gaps and then adjust the gaps to the recommended limits of the manufacturer. The oil control ring should be fitted first, before the middle and top rings with due regard to the nomenclature. If the piston and connecting rod assembly is to be installed into the cylinder, the innerliner of the cylinder should be polished and the edges should be chamfered. Do not lubricate the new bearing inserts as they are fitted and make sure that they sit in the correct position and that the piston ring gaps are arranged in the correct manner. Oil the piston and the rings, and then slip the piston/connecting rod into its corresponding cylinder avoiding to exert force on it. When the pistons have been installed, use Plastigage to determine the oil clearance of the connecting rod bearing and make sure that it is within the right provision. Where required, the bearing inserts should be replaced. Scrub off any Plastigage and lubricate the bearing surfaces; replace the rod cap and bolt it back down properly. Perform this for the other assemblies; one needs to make sure that they are properly cleaned and are well oriented. Last but not the least, turn the crankshaft in order to check for binding on bearings and to also measure for the connecting rod clearance if new con-rods and pins were fitted.

Genuine Honda Accord Connecting Rod

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Connecting Rods found

View related parts
Honda Accord Rod, Connecting
Part Number: 13210-R70-A00
$60.20 MSRP: $85.03
You Save: $24.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-RV0-A00, 13210-R70-A10
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2017 Honda Accord | 2 Door EX-L V6, 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Connrod Comp
Part Number: 13210-5A2-A00
$223.62 MSRP: $318.56
You Save: $94.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-R48-H00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2017 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX-S, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door SE, 4 Door Sport | KA 6MT, KA CVT, KL 6MT, KL CVT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-R40-A00
$175.75 MSRP: $250.34
You Save: $74.59 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-RLF-S00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door LX-S, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-PPA-000
$149.50 MSRP: $212.97
You Save: $63.47 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2007 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door EX-SUL, 2 Door LX, 2 Door LX-SUL, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door SE, 4 Door VP | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-5PA-A00
$66.80 MSRP: $94.36
You Save: $27.56 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-59B-000
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport, 4 Door Touring, EX-L, LX, Sport, Sport SE | KA 6MT, KA CVT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-5K0-A00
$137.32 MSRP: $195.62
You Save: $58.30 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014 Honda Accord | 4 Door Hybrid | KA CVT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-RDV-J00
$172.08 MSRP: $245.13
You Save: $73.05 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-P8C-A00, 13210-RCA-A00, 13210-P8A-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2007 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 4 Door EX (V6), 4 Door EX-V6, 4 Door LX (V6), 4 Door LX V6, 4 Door SE (V6) | KA 4AT, KA 5AT, KA 6MT, KL 4AT, KL 5AT, KL 6MT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-6C1-A00
$102.44 MSRP: $144.68
You Save: $42.24 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022 Honda Accord | Hybrid, Hybrid EX-L, Hybrid Sport, Hybrid Touring
View related parts
Honda Accord Connrod Comp
Part Number: 13210-RL5-T00
$145.91 MSRP: $207.85
You Save: $61.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013 Honda Accord | 4 Door EX, 4 Door LX | KA CVT
- 2011 Honda Accord | 4 Door LX | KA 5AT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-PH7-000
$121.89 MSRP: $173.63
You Save: $51.74 (30%)
ADD TO CART
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1997 Honda Accord | 4 Door EX (V6), 4 Door LX (V6) | KA 4AT, KL 4AT
View related parts
Honda Accord Rod Assy., Connecting
Part Number: 13210-689-000
$102.27 MSRP: $144.45
You Save: $42.18 (30%)
ADD TO CART
Product Specifications
- Replaced by: 13210-PB2-000
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1980 Honda Accord | 3 Door LX, 3 Door STD, 4 Door DX | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-RCA-A00
$172.08 MSRP: $245.13
You Save: $73.05 (30%)
ADD TO CART
Product Specifications
- Replaced by: 13210-RDV-J00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2001-2007 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 4 Door EX (V6), 4 Door LX (V6), 4 Door SE (V6) | KA 4AT, KA 5AT, KA 6MT, KL 5AT, KL 6MT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-6B2-A00
$60.01 MSRP: $84.76
You Save: $24.75 (30%)
Product Specifications
- Other Name: Connecting Rod
- Replaces: 13210-RPY-G10
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door (2.0 Sport), 4 Door (2.0 Touring), 4 Door EX-L (2.0), Sport, Touring | KA 6MT, KA XAT
View related parts
Honda Accord Rod Assy., Connecting
Part Number: 13210-PB2-000
Product Specifications
- Replaces: 13210-689-000
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1983 Honda Accord | 3 Door DX, 3 Door LX, 3 Door STD, 4 Door DX, 4 Door SE | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Accord Rod Assy., Connecting
Part Number: 13210-PC6-000
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1984-1989 Honda Accord | 2 Door DX, 2 Door LXI, 2 Door SEI, 3 Door DX, 3 Door LX, 3 Door LXI, 3 Door S, 4 Door DX, 4 Door LX, 4 Door LXI, 4 Door SEI, 4 Door STD | KA 4AT, KA 5MT, KH 4AT, KH 5MT, KL 4AT, KL 5MT
View related parts
Honda Accord Rod Assy., Connecting
Part Number: 13210-671-010
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1976-1978 Honda Accord | 3 Door LX, 3 Door STD | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-PT3-A00
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1990-1997 Honda Accord | 2 Door DX, 2 Door EX, 2 Door LX, 2 Door SE, 2 Door Special, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door LX, 4 Door SE, 4 Door Special, 5 Door EX, 5 Door LX | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Accord Rod, Connecting
Part Number: 13210-PAA-A00
$143.01 MSRP: $203.72
You Save: $60.71 (30%)
Product Specifications
- Other Name: Connecting Rod
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2002 Honda Accord | 2 Door EX, 2 Door LX, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door EX-SUL, 4 Door EX-UL, 4 Door LX, 4 Door SE, 4 Door SE-UL, 4 Door VP | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda Accord Connecting Rod

In search of affordable OEM Honda Accord Connecting Rod? Consider browsing through our extensive inventory of genuine Honda Accord Connecting Rod. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Accord Connecting Rod Parts Questions & Experts Answers

Rod, Connecting
13210-RDV-J00
Q: What steps must be taken before removing the piston and connecting rod assemblies on Honda Accord?
A: Before the assemblies of pistons and connecting rods can be dismantled the cylinder head and oil pan have to be disconnected. First, look that whether there is ridge formation at the upper limit of ring travel in each cylinder, if so than this must be done by ridge reamer for avoiding piston breakage. Once the ridges are turned to the top turn the engine onto its side so the Crankshaft is now at the top. After that, the connecting rod end-play has to be measured with the help of feeler gauges; it has to be within a given range; if it goes beyond this range, new connecting rods may be required. It is recommended to mark the connecting rods and caps to distinguish them before removing the connecting rod cap bolts and the cap itself, during which you should look for any traces of damage. Extract the connecting rod and piston assembly through the top of the engine and perform the same on all the cylinders. After removal, screw the connecting rod caps and setting geographical bearing inserts back into position and retain the old inserts especially for protection of surfaces. For piston ring installation, check the value of ring end gaps and then adjust the gaps to the recommended limits of the manufacturer. The oil control ring should be fitted first, before the middle and top rings with due regard to the nomenclature. If the piston and connecting rod assembly is to be installed into the cylinder, the innerliner of the cylinder should be polished and the edges should be chamfered. Do not lubricate the new bearing inserts as they are fitted and make sure that they sit in the correct position and that the piston ring gaps are arranged in the correct manner. Oil the piston and the rings, and then slip the piston/connecting rod into its corresponding cylinder avoiding to exert force on it. When the pistons have been installed, use Plastigage to determine the oil clearance of the connecting rod bearing and make sure that it is within the right provision. Where required, the bearing inserts should be replaced. Scrub off any Plastigage and lubricate the bearing surfaces; replace the rod cap and bolt it back down properly. Perform this for the other assemblies; one needs to make sure that they are properly cleaned and are well oriented. Last but not the least, turn the crankshaft in order to check for binding on bearings and to also measure for the connecting rod clearance if new con-rods and pins were fitted.