How to remove and install Oil Pressure Switch on Honda Prelude?

Low oil pressure warning lamp comes on with the ignition switch set to 'ON' with no engine running and turns on each time the oil pressure falls below a safe operating level with the running engine. To test the system first confirm the operation of the oil pressure light on selecting the 'ON' position with the ignition, and if the bulb does not illuminate, search for broken/connector wires around the engine and oil pressure switch. If the connector is present ground it to the engine using a jumper wire and then pull the lamp again. If it lights, ensure the oil pressure switch is grounded well and if it blinks replace the oil pressure switch; if it does not light, there might be a burned lamp or disconnected socket in the cluster instrument. When the oil pressure light is on continually, the levels of the oil should be checked and added to it if low; if the engine was low on oil, make test on the light after the addition of oil. That is, if light remains on then at the switch side of the wire remove the wire and then check the short circuit in the wire; if light is off then replace the oil pressure switch. If the light remains on while the engine is running, shut the engine for that the engine will not be damaged. Causes for the light to remain on include pinched or grounded sensor wire, gas switch went bad, the oil filter might be restricted or leaking, internal engine mechanical clearance may be bad or the oil is contaminated, or the screen to the oil pump pick-up may be blocked. For removal and installation, find the position of the oil pressure switch, write down the anti-theft code and radio settings, remove the negative battery terminal, electrical harness of the switch. To do it, use a pressure switch socket or wrench to remove the switch, and then put on the liquid thread sealant on the new unit and tighten the electrical connection, following which connects the battery, enter the code, start the engine, let it warm up, and inspect it for signs of leakage and good functioning.

Genuine Honda Prelude Oil Pressure Switch

Oil Pressure Sender Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Oil Pressure Switches found

View related parts
Honda Prelude Switch, Oil Pressure (Tec)
Part Number: 37240-PT0-014
$39.58 MSRP: $55.90
You Save: $16.32 (30%)
ADD TO CART
Product Specifications
- Other Name: Oil Pressure Sending Unit; Pressure Switch
- Replaces: 37240-PT0-003, 37240-P2F-A01, 37240-PD2-004, 37240-PT0-023, 37240-PT0-004, 37240-PD2-003, 37240-PT0-013
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985-2001 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0S, 2 Door 2.0SI, 2 Door DX, 2 Door S, 2 Door SI, 2 Door TYPESH | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Switch Assembly, Valve Timing Oil Pressure
Part Number: 37250-PR3-003
$115.22 MSRP: $162.74
You Save: $47.52 (30%)
ADD TO CART
Product Specifications
- Other Name: Oil Pressure Switch; Pressure Switch
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1993-2001 Honda Prelude | 2 Door Base, 2 Door Sivtec, 2 Door TYPESH | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Switch, Oil Pressure (Denso)
Part Number: 37240-PT0-023
$39.58 MSRP: $55.90
You Save: $16.32 (30%)
ADD TO CART
Product Specifications
- Replaced by: 37240-PT0-014
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1985-2001 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0S, 2 Door 2.0SI, 2 Door DX, 2 Door S, 2 Door SI, 2 Door TYPESH | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Switch Assembly, Oil Pressure (Denso)
Part Number: 37240-P13-013
$34.42 MSRP: $48.61
You Save: $14.19 (30%)
ADD TO CART
Product Specifications
- Other Name: Oil Pressure Sending Unit; Pressure Switch
- Replaces: 37240-657-013, 37240-P13-003, 35500-300-000, 37240-PCX-003, 31300-706-000, 35500-333-004, 35500-333-014, 37240-PA6-004, 37240-P13-004, 37600-611-154
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-2001 Honda Prelude | 2 Door Base, 2 Door SI, 2 Door Sivtec | KA 4AT, KA 5MT, KL 4AT, KL 5MT
- 1981-1985 Honda Prelude | 2 Door **, 2 Door DX | KA 4AT, KA 5MT, KA HMT, KH 4AT, KH 5MT, KH HMT, KL 4AT, KL 5MT, KL HMT
View related parts
Honda Prelude Switch, Oil Pressure
Part Number: 28600-P6H-013
$78.29 MSRP: $113.46
You Save: $35.17 (31%)
ADD TO CART
Product Specifications
- Replaced by: 28600-RCL-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda Prelude | 2 Door Base | KA 4AT, KL 4AT
View related parts
Honda Prelude Switch, Oil Pressure (Tec)
Part Number: 37240-PD2-004
$39.58 MSRP: $55.90
You Save: $16.32 (30%)
ADD TO CART
Product Specifications
- Other Name: Oil Pressure Sending Unit
- Replaced by: 37240-PT0-014
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1991 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0S, 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Switch, Oil Pressure (Denso)
Part Number: 37240-657-013
$34.42 MSRP: $48.61
You Save: $14.19 (30%)
ADD TO CART
Product Specifications
- Replaced by: 37240-P13-013
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1981-1985 Honda Prelude | 2 Door **, 2 Door DX | KA 4AT, KA 5MT, KA HMT, KH 4AT, KH 5MT, KH HMT, KL 4AT, KL 5MT, KL HMT
View related parts
Honda Prelude Sensor, Oil Pressure
Part Number: 48150-P6K-003
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda Prelude | 2 Door TYPESH | KA 5MT, KL 5MT
View related parts
Honda Prelude Switch, Oil Pressure
Part Number: 37240-657-305
Product Specifications
- Replaces: 37240-657-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979-1981 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT, KL 5MT, KL HMT
View related parts
Honda Prelude Switch Assembly, Oil Pressure (Tec)
Part Number: 37240-P13-014
Product Specifications
- Other Name: Oil Pressure Sending Unit; Pressure Switch
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1996 Honda Prelude | 2 Door SI, 2 Door Sivtec | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda Prelude Oil Pressure Switch

Oil Pressure Switch is very important in Honda prelude car model through it carry out the process of monitoring the pressure of the oil utilized by the motor. Its main use is to inform the driver whenever the oil pressure is out of the normal range thus pose some danger to the engine. In the course of the years, Honda Prelude used different types of Oil Pressure Switches being aimed at performing this monitoring function. While specific differences between these types are not detailed, the fundamental mechanism remains consistent: for measuring the levels of oil pressure and further informing feedback to other operations of the car. In total, the Oil Pressure Switch is important for the reliability of the engine of the Honda Prelude.

In search of affordable OEM Honda Prelude Oil Pressure Switch? Consider browsing through our extensive inventory of genuine Honda Prelude Oil Pressure Switch. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Prelude Oil Pressure Switch Parts Questions & Experts Answers

Switch Assembly, Oil Pressure (Denso)
37240-P13-013
Q: How to remove and install Oil Pressure Switch on Honda Prelude?
A: Low oil pressure warning lamp comes on with the ignition switch set to 'ON' with no engine running and turns on each time the oil pressure falls below a safe operating level with the running engine. To test the system first confirm the operation of the oil pressure light on selecting the 'ON' position with the ignition, and if the bulb does not illuminate, search for broken/connector wires around the engine and oil pressure switch. If the connector is present ground it to the engine using a jumper wire and then pull the lamp again. If it lights, ensure the oil pressure switch is grounded well and if it blinks replace the oil pressure switch; if it does not light, there might be a burned lamp or disconnected socket in the cluster instrument. When the oil pressure light is on continually, the levels of the oil should be checked and added to it if low; if the engine was low on oil, make test on the light after the addition of oil. That is, if light remains on then at the switch side of the wire remove the wire and then check the short circuit in the wire; if light is off then replace the oil pressure switch. If the light remains on while the engine is running, shut the engine for that the engine will not be damaged. Causes for the light to remain on include pinched or grounded sensor wire, gas switch went bad, the oil filter might be restricted or leaking, internal engine mechanical clearance may be bad or the oil is contaminated, or the screen to the oil pump pick-up may be blocked. For removal and installation, find the position of the oil pressure switch, write down the anti-theft code and radio settings, remove the negative battery terminal, electrical harness of the switch. To do it, use a pressure switch socket or wrench to remove the switch, and then put on the liquid thread sealant on the new unit and tighten the electrical connection, following which connects the battery, enter the code, start the engine, let it warm up, and inspect it for signs of leakage and good functioning.