Where is the Intake Air Temperature (IAT) Sensor Located on Honda Passport?

The Intake Manifold Temperature Sensor is on the air intake duct. It is a thermistor that changes its resistance in proportion to engine temperature. The PCM supplies a 5-volt reference voltage to the Intake Manifold Temperature Sensor and uses the signal to adjust spark timing. A failure of the Intake Manifold Temperature Sensor will cause the PCM to set diagnostic trouble code P0112 or P01To check it, disconnect the two-prong electrical connector and measure the reference voltage. To replace it, disconnect the cable from the negative battery terminal and unplug the electrical connector. Pull on the sensor while rocking it from side to side to disengage it from the grommet. Installation is the reverse of removal.

Genuine Honda Passport Intake Manifold Temperature Sensor

Air Intake Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Intake Manifold Temperature Sensors found

View related parts
Honda Passport Sensor, In. Air Temperature
Part Number: 8-25037-334-0
Product Specifications
- Other Name: Air Intake Temp Sensor; Air Intake Temperature Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1994-1995 Honda Passport | 4 Door EX (4X4 V6), 4 Door EX-W (4X4 V6), 4 Door LX (4X2 V6), 4 Door LX (4X4 V6), 4 Door LX-W (4X4 V6) | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Passport Sensor, Temperature
Part Number: 8-12160-244-0
Product Specifications
- Other Name: Air Intake Temp Sensor; Air Intake Temperature Sensor, Temperature Sensor
- Replaces: 8-12110-319-0
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996-2002 Honda Passport | 4 Door 2EX, 4 Door 2EX-L, 4 Door 2LX, 4 Door 4EX, 4 Door 4EX-L, 4 Door 4LX, 4 Door 4LX-W, 4 Door DX, 4 Door EX-W (4X2 V6), 4 Door EX-W (4X4 V6), 4 Door LX (4X2 V6), 4 Door LX (4X4 V6), 4 Door LX-W (4X4 V6) | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda Passport Intake Manifold Temperature Sensor

The Intake Manifold Temperature Sensor in Honda Passport vehicles is responsible for the measurement of the air temperature that is taken into the combustion chamber in order to make provisions for right combustion and great performance of the vehicles. This information is then fed back to the PCM so as to appropriately modify the fuel injector timing in order to attain the correct air/fuel ratio at different operating conditions. There might be several Intake Manifold Temperature Sensors used in the different models of Passport produced over the years to match optimum sensitivity to certain air flow rates. If the sensor is faulty, it can cause poor running, examples include, the car lagging while accelerating or the car stalling and if severe enough, it can set off a Diagnostic Trouble Code or DTC in the engine control module. There is therefore the need to ensure the smooth working of the Intake Air Temperature Sensor for the engine to run smoothly.

In search of affordable OEM Honda Passport Intake Manifold Temperature Sensor? Consider browsing through our extensive inventory of genuine Honda Passport Intake Manifold Temperature Sensor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Passport Intake Manifold Temperature Sensor Parts Questions & Experts Answers

Sensor, Temperature
8-12160-244-0
Q: Where is the Intake Air Temperature (IAT) Sensor Located on Honda Passport?
A: The Intake Manifold Temperature Sensor is on the air intake duct. It is a thermistor that changes its resistance in proportion to engine temperature. The PCM supplies a 5-volt reference voltage to the Intake Manifold Temperature Sensor and uses the signal to adjust spark timing. A failure of the Intake Manifold Temperature Sensor will cause the PCM to set diagnostic trouble code P0112 or P01To check it, disconnect the two-prong electrical connector and measure the reference voltage. To replace it, disconnect the cable from the negative battery terminal and unplug the electrical connector. Pull on the sensor while rocking it from side to side to disengage it from the grommet. Installation is the reverse of removal.