How to safely remove and install a strut assembly on Honda Odyssey?

Before removing the wheel, one has to unscrew the wheel lug nuts ,lift the vehicle and properly jack it using the jackstands. Loosen the nuts on the strut and separate the stabilizer bar link from the strut, also, the brake hose bracket must also be removed from the strut. Unbolt the clamp bracket to remove the ABS speed sensor wiring harness also from the strut. Locate the strut relative to the knuckle to match it up, after which unscrew the strut-to-knuckle nuts and use a hammer and punch to extract the bolts. Very delicately introduce a slight space between the strut and the steering knuckle not to stretch the inner CV joint anymore or let the steering knuckle drops on the opposite direction that might harm the brake hose. Hold the strut and spring assembly in one hand and take off the three upper mounting nuts and finally take the assembly out of the fenderwell. Look for indications of strut body leaks, dents, cracks and other sign of wear and possible need of repair or replacement, that concerns the coil spring check for chipped or cracked painting of the spring in addition to the spring seat that should not have cuts or other signs of deterioration. If any problems are detected, go on to dismantle the strut. To assemble it, guide the strut assembly into the fenderwell and place three upper mounting studs through the shock tower holes and tighten nuts in order to hold the from falling. Position the steering knuckle into the strut flange, put the two bolts into the holes and adjust the marks made prior to disassembling; then tighten the nuts to the correct torque and replace the fasteners where necessary. Brake hose bracket, speed sensor wiring harness and the stabilizer bar link needs to be reinstalled. Lastly, secure the wheel and finish putting the lugs nuts over it, and then lower the car, respectively tighten the lugs nuts to the required torque tightening, further tighten the three upper mounting nuts and lastly ensure that you check and adjust the front wheel alignment if it is out of alignment.

Genuine Honda Odyssey Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

96 Shock Absorbers found

View related parts
Honda Odyssey Shock Absorber Unit, Left Front
Part Number: 51621-THR-A02
$246.26 MSRP: $350.81
You Save: $104.55 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door EX, 5 Door EX (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door LX, 5 Door LX (10AT), 5 Door Touring (10AT), EX, EX-L, Sport, Touring | KA 9AT, KA XAT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-THR-A22
$116.04 MSRP: $163.90
You Save: $47.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock, Shock Absorber
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), Elite | KA XAT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51611-THR-A02
$246.26 MSRP: $350.81
You Save: $104.55 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door EX, 5 Door EX (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door LX, 5 Door LX (10AT), 5 Door Touring (10AT), EX, EX-L, Sport, Touring | KA 9AT, KA XAT
View related parts
Honda Odyssey Shock Absorber Unit, Left Front
Part Number: 51606-TK8-A03
$217.18 MSRP: $309.37
You Save: $92.19 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2012 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51611-THR-A92
$246.26 MSRP: $350.81
You Save: $104.55 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), Elite | KA XAT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-TK8-A03
$217.18 MSRP: $309.37
You Save: $92.19 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2012 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Shock Absorber Unit, Left Front
Part Number: 51606-S0X-A05
$189.50 MSRP: $310.50
You Save: $121.00 (39%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Replaces: 51606-S0X-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door VAN | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-S0X-A05
$180.27 MSRP: $256.81
You Save: $76.54 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Replaces: 51605-S0X-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door VAN | KA 5AT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-SHJ-L01
$172.06 MSRP: $245.09
You Save: $73.03 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-SHJ-L01
$225.97 MSRP: $321.91
You Save: $95.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door EX, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-SHJ-A03
$172.06 MSRP: $245.09
You Save: $73.03 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2007 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-SHJ-A04
$220.67 MSRP: $314.35
You Save: $93.68 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Replaces: 51605-SHJ-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-S0X-A04
$168.73 MSRP: $240.36
You Save: $71.63 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Replaces: 52610-S0X-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door VAN | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-SHJ-A31
$220.67 MSRP: $314.35
You Save: $93.68 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Left Front
Part Number: 51606-SHJ-A04
$231.45 MSRP: $329.71
You Save: $98.26 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Replaces: 51606-SHJ-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-SHJ-L71
$172.06 MSRP: $245.09
You Save: $73.03 (30%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Shock Absorber Unit, Left Front
Part Number: 51621-THR-A92
$246.26 MSRP: $350.81
You Save: $104.55 (30%)
ADD TO CART
Product Specifications
- Other Name: Strut
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), Elite | KA XAT
View related parts
Honda Odyssey Shock Absorber, Rear
Part Number: 52610-TK8-A11
$126.15 MSRP: $179.70
You Save: $53.55 (30%)
Product Specifications
- Other Name: Shock Absorber; Shock
- Position: Rear
- Replaces: 52610-TK8-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Shock Absorber Unit, Right Front
Part Number: 51605-TK8-A04
$206.18 MSRP: $293.69
You Save: $87.51 (30%)
Product Specifications
- Other Name: Strut
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Shock Absorber Assembly, Rear
Part Number: 52610-THR-A02
$116.04 MSRP: $163.90
You Save: $47.86 (30%)
Product Specifications
- Other Name: Shock, Shock Absorber
- Position: Rear
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door EX, 5 Door EX (10AT), 5 Door LX, 5 Door LX (10AT), EX | KA 9AT, KA XAT

| Page 1 of 5 |Next >

1-20 of 96 Results

Honda Odyssey Shock Absorber

The Shock Absorber is an important part of the car suspension system which is an integral part of Honda Odyssey, it's its mandate to minimize any extra bouncing and instead this part will help to provide the prime ride for the car. Indeed, due to transformation of kinetic energy into heat through the means of hydraulic mechanisms the Shock Absorber also eliminates vibrations during the motion and optimizes handling, especially in the rough road conditions. In the past decades, Honda Odyssey has employed several kinds of Shock Absorbers, the twin-tube and the mono-tube shock absorbers. Twin-tube shocks are normal they include simple construction that can be gas charged for increased toughness. On the other hand, it is found that monotube shocks have better heat management and working ability and are compatible with multi-axial installation. Other option such as Position Sensitive Damping (PSD) and Acceleration Sensitive Damping (ASD) takes the control to the extreme by allowing specific conditions and reflects the development of the Honda Odyssey suspension tech.

In search of affordable OEM Honda Odyssey Shock Absorber? Consider browsing through our extensive inventory of genuine Honda Odyssey Shock Absorber. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Odyssey Shock Absorber Parts Questions & Experts Answers

Shock Absorber Assembly, Rear
52610-S0X-A04
Q: How to safely remove and install a strut assembly on Honda Odyssey?
A: Before removing the wheel, one has to unscrew the wheel lug nuts ,lift the vehicle and properly jack it using the jackstands. Loosen the nuts on the strut and separate the stabilizer bar link from the strut, also, the brake hose bracket must also be removed from the strut. Unbolt the clamp bracket to remove the ABS speed sensor wiring harness also from the strut. Locate the strut relative to the knuckle to match it up, after which unscrew the strut-to-knuckle nuts and use a hammer and punch to extract the bolts. Very delicately introduce a slight space between the strut and the Steering Knuckle not to stretch the inner CV joint anymore or let the steering knuckle drops on the opposite direction that might harm the brake hose. Hold the strut and spring assembly in one hand and take off the three upper mounting nuts and finally take the assembly out of the fenderwell. Look for indications of strut body leaks, dents, cracks and other sign of wear and possible need of repair or replacement, that concerns the coil spring check for chipped or cracked painting of the spring in addition to the spring seat that should not have cuts or other signs of deterioration. If any problems are detected, go on to dismantle the strut. To assemble it, guide the strut assembly into the fenderwell and place three upper mounting studs through the shock tower holes and tighten nuts in order to hold the from falling. Position the steering knuckle into the strut flange, put the two bolts into the holes and adjust the marks made prior to disassembling; then tighten the nuts to the correct torque and replace the fasteners where necessary. Brake hose bracket, speed sensor wiring harness and the stabilizer bar link needs to be reinstalled. Lastly, secure the wheel and finish putting the lugs nuts over it, and then lower the car, respectively tighten the lugs nuts to the required torque tightening, further tighten the three upper mounting nuts and lastly ensure that you check and adjust the front wheel alignment if it is out of alignment.