How do you remove and install the IAT sensor on Honda Odyssey?

For all models except 2008 and later with VCM proceed with the following, Pull the ignition key out of the key lock cylinder. Turn the intake manifold cover unions counter-clockwise and then lift off the intake manifold cover. Then, release the electrical connector from the Intake Manifold Temperature Sensor which is to be done by pushing on the tab on the bottom of the connector then pulling it back. Loosen and pull the Intake Manifold Temperature Sensor out, which should be done because of the low quality of the Intake Manifold Temperature Sensor O-ring. To correctly fit the Intake Manifold Temperature Sensor, one should install a new O-ring, this is regardless of whether the sensor that was initially used was retained or replaced with a new one. The procedure of installing the Intake Manifold Temperature Sensor is opposite to that of the removal and it is recommended that a new O-ring is fitted and re-tightening of the Intake Manifold Temperature Sensor is done to the right torque. For DTCS P0135 and P0141 for 1996 to 2007 models, as well as other genera related to VCM for the 2008 and later models, the Intake Manifold Temperature Sensor is incorporated with the MAF sensor.

Genuine Honda Odyssey Intake Manifold Temperature Sensor

Air Intake Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Intake Manifold Temperature Sensors found

View related parts
Honda Odyssey Sensor Assembly, Air Temperature
Part Number: 37880-P0A-A02
$67.09 MSRP: $94.77
You Save: $27.68 (30%)
ADD TO CART
Product Specifications
- Other Name: Air Intake Temp Sensor; Air Intake Temperature Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door LX (6 Seats), 5 Door LX (7 Seats), 5 Door VAN | KA 4AT, KA 5AT
View related parts
Honda Odyssey Sensor Assembly, Air Temperature
Part Number: 37880-PDA-E01
$58.12 MSRP: $82.08
You Save: $23.96 (30%)
ADD TO CART
Product Specifications
- Other Name: Air Intake Temp Sensor; Air Intake Temperature Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT

Honda Odyssey Intake Manifold Temperature Sensor

The Intake Manifold Temperature Sensor in vehicles particularly in Honda Odyssey helps in regulating the temperature of the inflowing air towards the engine to help in improving combustion quality of the engine. All this information is communicated to the PCM and with the use of signals it alters the fuel injector timing to ensure the appropriate air/fuel ratio for different operating conditions. In this guide, Honda Odyssey has employed various Intake Manifold Temperature Sensors which include the Mass Air Flow (MAF) sensors and, Velocity Air Flow (VAF) sensors. These two kinds are thermostatically balanced to achieve specific ranges of air flow and also optimized to complement particular fuel injectors. Changes to these sensors are expressed in their tolerance for higher airflow rates when modifications to the car's intake system occur such as a larger throttle body or high flow fuel injectors. Intermittent or permanent failure of the Intake Manifold Temperature Sensor can cause some problems, namely, stalling or incorrect air/fuel mixture.

In search of affordable OEM Honda Odyssey Intake Manifold Temperature Sensor? Consider browsing through our extensive inventory of genuine Honda Odyssey Intake Manifold Temperature Sensor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Odyssey Intake Manifold Temperature Sensor Parts Questions & Experts Answers

Sensor Assembly, Air Temperature
37880-P0A-A02
Q: How do you remove and install the IAT sensor on Honda Odyssey?
A: For all models except 2008 and later with VCM proceed with the following, Pull the ignition key out of the key lock cylinder. Turn the intake manifold cover unions counter-clockwise and then lift off the intake manifold cover. Then, release the electrical connector from the Intake Manifold Temperature Sensor which is to be done by pushing on the tab on the bottom of the connector then pulling it back. Loosen and pull the Intake Manifold Temperature Sensor out, which should be done because of the low quality of the Intake Manifold Temperature Sensor O-ring. To correctly fit the Intake Manifold Temperature Sensor, one should install a new O-ring, this is regardless of whether the sensor that was initially used was retained or replaced with a new one. The procedure of installing the Intake Manifold Temperature Sensor is opposite to that of the removal and it is recommended that a new O-ring is fitted and re-tightening of the Intake Manifold Temperature Sensor is done to the right torque. For DTCS P0135 and P0141 for 1996 to 2007 models, as well as other genera related to VCM for the 2008 and later models, the Intake Manifold Temperature Sensor is incorporated with the MAF sensor.