How do you replace the hood latch and hood release cable on Honda Odyssey?

To replace the latch you should first remove the covering that may be on top of the grille if present, then marking the line around the latch bolts to enable alignment, then removing the bolts holding the hood latch to the radiator support and then removing the latch. Thirdly, there is the requirement to disconnect the hood release cable from the latch assembly as it involves detaching the housing of the cable and pulling out the end of the cable from the latch. Reinstallation is done in a reverse order to removal; however, the latch has to be correctly aligned, such that, when closed with the bumpers being slightly compressed the hood engages. Start on the cable, by pulling out the driver's side kick panel followed by pulling out the hood release handle which has mounting bolts. Press the 'hood release handle lever upward position', turn the end of the cable to the right and remove the cable from the handle. Place one end of a piece of wire or string inside the vehicle by the left front terminal of the cable and then loosen the left front wheel lug nuts, raise the assembly and support it by jackstands before removing the left inner fender splash shield. On the engine compartment, remove all the hood release cable from the latch and release all the cable retention clips of the radiator support and inner fenderwell. Slide the cable out and to the front if possible then either undo the wire or string tied around the old cable and secure it around the new cable instead. When the new cable is in place pull the wire or string back through the firewall until the new cable runs to the inside handle and install the cable grommet where it passes through the body of the vehicle. Last but not the least fix the new cable to the hood release handle, make sure that the cable housing fits properly into the notch of the handle bracket, then finally tighten the lug nuts of the wheel to the required torque.

Genuine Honda Odyssey Hood Latch

Engine Hood Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Hood Latches found

View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-THR-A12
$41.72 MSRP: $58.93
You Save: $17.21 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock, Lock Assembly
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2024 Honda Odyssey | 5 Door ELITE (10AT), 5 Door EX, 5 Door EX (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door LX, 5 Door LX (10AT), 5 Door Touring (10AT), EX, EX-L, Elite, Sport, Touring | KA 9AT, KA XAT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-TK8-507
$250.37 MSRP: $356.65
You Save: $106.28 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock, Lock Assembly
- Replaces: 74120-TK8-A31
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door SE, 5 Door Touring | KA 6AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-S0X-506
$303.57 MSRP: $432.43
You Save: $128.86 (30%)
ADD TO CART
Product Specifications
- Replaces: 74120-S0X-A20
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L | KA 4AT, KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-TK8-A31
$250.37 MSRP: $356.65
You Save: $106.28 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly
- Replaced by: 74120-TK8-507
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door SE, 5 Door Touring | KA 6AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-S0X-A20
$303.57 MSRP: $432.43
You Save: $128.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock
- Replaced by: 74120-S0X-506
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L | KA 4AT, KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood (Security)
Part Number: 74120-TK8-A11
$259.40 MSRP: $369.52
You Save: $110.12 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly
- Replaced by: 74120-TK8-506
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-A11
$189.43 MSRP: $269.85
You Save: $80.42 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Lock
- Replaced by: 74120-SHJ-507
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-A01
$70.23 MSRP: $460.00
You Save: $389.77 (85%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Lock
- Replaced by: 74120-SHJ-505
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2007 Honda Odyssey | 5 Door LX | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-A13
$187.11 MSRP: $266.53
You Save: $79.42 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly
- Replaced by: 74120-SHJ-509
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-S0X-505
$273.25 MSRP: $389.25
You Save: $116.00 (30%)
ADD TO CART
Product Specifications
- Replaces: 74120-S0X-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1999-2004 Honda Odyssey | 5 Door EX, 5 Door LX, 5 Door VAN | KA 4AT, KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-S0X-A01
$273.25 MSRP: $389.25
You Save: $116.00 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly
- Replaced by: 74120-S0X-505
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1999-2004 Honda Odyssey | 5 Door EX, 5 Door LX, 5 Door VAN | KA 4AT, KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-507
$189.43 MSRP: $269.85
You Save: $80.42 (30%)
ADD TO CART
Product Specifications
- Replaces: 74120-SHJ-A11
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-A02
$127.06 MSRP: $181.00
You Save: $53.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door LX | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-TK8-A01
$76.41 MSRP: $107.92
You Save: $31.51 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Honda Odyssey | 5 Door LX | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-509
$187.11 MSRP: $266.53
You Save: $79.42 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock, Lock Assembly
- Replaces: 74120-SHJ-A13
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-A12
$214.75 MSRP: $305.92
You Save: $91.17 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly; Lock
- Replaced by: 74120-SHJ-508
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-TK8-505
$227.89 MSRP: $324.63
You Save: $96.74 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock, Lock Assembly
- Replaces: 74120-TK8-A21
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Honda Odyssey | 5 Door LX | KA 6AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SHJ-505
$322.92 MSRP: $460.00
You Save: $137.08 (30%)
ADD TO CART
Product Specifications
- Replaces: 74120-SHJ-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2007 Honda Odyssey | 5 Door LX | KA 5AT
View related parts
Honda Odyssey Lock Assembly, Hood
Part Number: 74120-SX0-A01
Product Specifications
- Other Name: Lock Assembly; Lock
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Honda Odyssey | 5 Door EX, 5 Door LX (6 Seats), 5 Door LX (7 Seats) | KA 4AT

Honda Odyssey Hood Latch

Thus, the Hood Latch in Honda Odyssey automobiles plays a significant role of fixing the hood in a way that is cannot open during operations. This component is designed to be located directly under the front of the hood with critical components such as the engine, the radiator and battery well shielded. If ever Honda Odyssey models were made over the years, it is probable that there may have been changes in Hood Latch design, however, what kinds of types or styles are not clear. The first still stays the same, it accentuates the steadiness and the security of the hood to ensure it stays shut while driving. In general, the Honda Odyssey Hood Latch is required to preserve the functionality of significant systems of the automobile.

In search of affordable OEM Honda Odyssey Hood Latch? Consider browsing through our extensive inventory of genuine Honda Odyssey Hood Latch. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Odyssey Hood Latch Parts Questions & Experts Answers

Lock Assembly, Hood
74120-S0X-A01
Q: How do you replace the hood latch and hood release cable on Honda Odyssey?
A: To replace the latch you should first remove the covering that may be on top of the Grille if present, then marking the line around the latch bolts to enable alignment, then removing the bolts holding the hood latch to the radiator support and then removing the latch. Thirdly, there is the requirement to disconnect the hood release cable from the latch assembly as it involves detaching the housing of the cable and pulling out the end of the cable from the latch. Reinstallation is done in a reverse order to removal; however, the latch has to be correctly aligned, such that, when closed with the bumpers being slightly compressed the hood engages. Start on the cable, by pulling out the driver's side kick panel followed by pulling out the hood release handle which has mounting bolts. Press the 'hood release handle lever upward position', turn the end of the cable to the right and remove the cable from the handle. Place one end of a piece of wire or string inside the vehicle by the left front terminal of the cable and then loosen the left front wheel lug nuts, raise the assembly and support it by jackstands before removing the left inner fender splash shield. On the engine compartment, remove all the hood release cable from the latch and release all the cable retention clips of the radiator support and inner fenderwell. Slide the cable out and to the front if possible then either undo the wire or string tied around the old cable and secure it around the new cable instead. When the new cable is in place pull the wire or string back through the firewall until the new cable runs to the inside handle and install the cable grommet where it passes through the body of the vehicle. Last but not the least fix the new cable to the hood release handle, make sure that the cable housing fits properly into the notch of the handle bracket, then finally tighten the lug nuts of the wheel to the required torque.