Contact Us: Live Chat or 1-888-984-2011
My Garage
My Account
My Cart

Genuine Honda Fit Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Enter your vehicle info to find more parts and verify fitment

  • Select Vehicle by VIN
  • Select Vehicle by Model
Select by VIN
Enter your VIN for the most accurate results.
Enter your VIN for the most accurate results.
or
Select by Model
-- Select Model --
-- Select Year --
-- Select Body & Trim --
-- Select Emission & Transmission --

3 Crankshaft Pulleys found

  • Honda Fit Crankshaft Pulley - 13810-PWC-013
    Diagram for Honda Fit Crankshaft Pulley - 13810-PWC-013
    View related parts

    Honda Fit Pulley, Crankshaft

    Part Number: 13810-PWC-013
    • Other Name: Crankshaft Pulley; Pulley
    • Replaces: 13810-PWC-003
    $124.21 MSRP: $176.94
    You Save: $52.73 (30%)
    Add to Cart
    More Info
    Fits the following Vehicles:
    • 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT, KA 5MT
    Less Info
  • Honda Fit Crankshaft Pulley - 13810-RB0-003
    Diagram for Honda Fit Crankshaft Pulley - 13810-RB0-003
    View related parts

    Honda Fit Pulley, Crankshaft

    Part Number: 13810-RB0-003
    • Other Name: Crankshaft Pulley; Pulley
    $131.32 MSRP: $187.07
    You Save: $55.75 (30%)
    Add to Cart
    More Info
    Fits the following Vehicles:
    • 2009-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT, KA 5MT
    Less Info
  • Honda Fit Crankshaft Pulley - 13810-5R0-003
    Diagram for Honda Fit Crankshaft Pulley - 13810-5R0-003
    View related parts

    Honda Fit Pulley, Crankshaft

    Part Number: 13810-5R0-003
    • Other Name: Crankshaft Pulley; Pulley
    $341.41 MSRP: $486.34
    You Save: $144.93 (30%)
    Add to Cart
    More Info
    Fits the following Vehicles:
    • 2015-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA 6MT, KA CVT
    Less Info

Honda Fit Crankshaft Pulley Parts Questions & Answers

  • Q: How do you replace the front crankshaft seal and Crankshaft Pulley on Honda Fit?
    A: Disconnect the cable from the negative battery terminal. Raise the vehicle and support it securely on jackstands, then remove the wheel and the splash shield from below the engine compartment. Loosen the crankshaft pulley bolt using a special tool that engages with the recessed hex in the pulley opening to prevent the crankshaft from turning while unscrewing the bolt. If a special tool is unavailable, remove the flywheel/driveplate inspection cover and wedge a screwdriver into the starter ring gear teeth. Slip the pulley off the crankshaft. Carefully pry the seal out of the timing chain cover with a seal removal tool or a screwdriver, taking care not to scratch the seal bore or damage the crankshaft, as damage will cause the new seal to leak. Clean the bore in the seal housing and coat the outer edge of the new seal with engine oil or multi-purpose grease. Using a seal driver or a socket with an outside diameter slightly smaller than that of the seal, carefully drive the seal into place with a hammer; if a socket is not available, a short section of a large diameter pipe will suffice. After installation, check the seal to ensure the spring did not pop out. Lubricate the lip of the seal with a thin film of engine oil or multi-purpose grease, and lubricate the pulley bolt threads and the surface between the washer and bolt head with clean engine oil before installing the crankshaft pulley and tightening it to the specified torque. The remainder of the installation follows the reverse order of removal. Finally, run the engine and check for leaks.

Related Honda Fit Parts

About Honda Fit Crankshaft Pulley

A Honda Fit needs to be kept in good working condition in your vehicle. The online catalog we provide will get you through the ordering process safely and securely. All genuine Honda Crankshaft Pulleys from us are shipped directly from authorized Honda Dealer. If you want search for Honda Crankshaft Pulley fast and easily, just come to Hondapartsnow.com to look for your parts.