How to remove and install the Steering Knuckle and hub for the Honda Crosstour?

To remove the front wheel, the lug nuts should be loosened, raising of the vehicle and supporting it using jack stands. Also, remove the wheel and loosen the axle nut. Take off the brake caliper and disc, loosen drive axle/hub nut, and disconnect the control arm and tie-rod end. It is also possible to take off the knuckle and hub assembly or replace wheel bearing if necessary. On installation of drive axle splines it will be necessary to grease them, and reengage ball joints, brake disc, and caliper.

How to remove and install the rear Steering Knuckle for the Honda Crosstour?

To remove the rear wheel, loosen the lug nuts, raise the vehicle, and remove the wheel. To remove a disc brake, unbolt the brake hose bracket, caliper and mounting bracket; then take off the brake disk, hub and bearing assembly, and splash guard. For drum, brakes, disconnect the brake line and remove the hub, bearing assembly, and backing plate bolts. Disconnect the stabilizer bar link, shock absorber assembly, and suspension arm from the steering knuckle. If needed replace hub and bearing assembly. For installation, connect suspension arms to steering knuckle with shock absorber as well as stabilizer bar link. Put back in place hub and bearing assembly along with brake components. Bleed drum brakes for brake system.

Genuine Honda Crosstour Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Steering Knuckles found

View related parts
Honda Crosstour Knuckle, Right Front
Part Number: 51210-TP6-A00
$313.52 MSRP: $446.62
You Save: $133.10 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX, 5 Door EX (2WD), 5 Door EX-L, 5 Door EX-L (2WD), 5 Door EX-L (4WD) | KA 5AT, KA 6AT
View related parts
Honda Crosstour Knuckle, Left Front
Part Number: 51215-TP6-A00
$313.52 MSRP: $446.62
You Save: $133.10 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX, 5 Door EX (2WD), 5 Door EX-L, 5 Door EX-L (2WD), 5 Door EX-L (4WD) | KA 5AT, KA 6AT
View related parts
Honda Crosstour Knuckle, Left Rear
Part Number: 52215-TP6-A01
$222.39 MSRP: $316.79
You Save: $94.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX, 5 Door EX (2WD), 5 Door EX-L, 5 Door EX-L (2WD) | KA 5AT, KA 6AT
View related parts
Honda Crosstour Knuckle, Right Rear
Part Number: 52210-TP7-A01
$222.39 MSRP: $316.79
You Save: $94.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX-L (4WD) | KA 5AT, KA 6AT
View related parts
Honda Crosstour Knuckle, Left Rear
Part Number: 52215-TP7-A01
$222.39 MSRP: $316.79
You Save: $94.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX-L (4WD) | KA 5AT, KA 6AT
View related parts
Honda Crosstour Knuckle, Right Rear
Part Number: 52210-TP6-A01
$222.39 MSRP: $316.79
You Save: $94.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2010-2015 Honda Crosstour | 5 Door EX, 5 Door EX (2WD), 5 Door EX-L, 5 Door EX-L (2WD) | KA 5AT, KA 6AT

Honda Crosstour Steering Knuckle

The steering Steering Steering Knuckle in Honda Crosstour vehicles is the component that brings out the link between the suspension and the steering systems to enable the movement of the front wheels. At which it offers mountings for the control arms, and tie rods and the wheel hub or spindle, so as it could provide the vertical and horizontal wheel travel relative to road inputs and the turning relative to the front axle. Crosstour steering knuckles can be classified as per their drive type, FWD or AWD. Specifically, in FWD/AWD applications the knuckle includes a hub that links to drive axle and in RWD designs may include an integral spindle. Variations are incorporated in the design to improve on the performance and stability of the knuckle where the role of the knuckle is to contain the wheel and prevent it from swerving during use. The knuckle must be inspected often since it may wear out after a few suspension component replacements are made.

In search of affordable OEM Honda Crosstour Steering Knuckle? Consider browsing through our extensive inventory of genuine Honda Crosstour Steering Knuckle. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Crosstour Steering Knuckle Parts Questions & Experts Answers

Knuckle, Right Rear
52210-TP7-A01
Q: How to remove and install the Steering Knuckle and hub for the Honda Crosstour?
A: To remove the front wheel, the lug nuts should be loosened, raising of the vehicle and supporting it using jack stands. Also, remove the wheel and loosen the axle nut. Take off the brake caliper and disc, loosen drive axle/hub nut, and disconnect the Control Arm and tie-rod end. It is also possible to take off the knuckle and hub assembly or replace wheel bearing if necessary. On installation of drive axle splines it will be necessary to grease them, and reengage Ball Joints, brake disc, and caliper.
Knuckle, Left Rear
52215-TP6-A01
Q: How to remove and install the rear Steering Knuckle for the Honda Crosstour?
A: To remove the rear wheel, loosen the lug nuts, raise the vehicle, and remove the wheel. To remove a disc brake, unbolt the brake hose bracket, caliper and mounting bracket; then take off the brake disk, hub and bearing assembly, and splash guard. For drum, brakes, disconnect the brake line and remove the hub, bearing assembly, and backing plate bolts. Disconnect the stabilizer bar link, Shock Absorber assembly, and suspension arm from the steering knuckle. If needed replace hub and bearing assembly. For installation, connect suspension arms to steering knuckle with shock absorber as well as stabilizer bar link. Put back in place hub and bearing assembly along with brake components. Bleed drum brakes for brake system.