Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2008-2012 Honda Accord | 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KL 5AT, KL 5MT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2008-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door EX-L V6, 2 Door LX, 2 Door LX-S, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KA 6MT, KL 5AT, KL 5MT, KL 6MT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2008-2012 Honda Accord | 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KL 5AT, KL 5MT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2008-2012 Honda Accord | 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KL 5AT, KL 5MT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
1994-1997 Honda Accord | 2 Door DX, 2 Door EX, 2 Door LX, 2 Door Special, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door EX (V6), 4 Door LX, 4 Door LX (V6), 4 Door Special, 5 Door EX, 5 Door LX | KA 4AT, KA 5MT, KL 4AT, KL 5MT
| Page 1 of 5 |Next >
1-20 of 90 Results
Honda Accord Rack And Pinion Parts Questions & Experts Answers
Q: How to remove and reinstall the steering gear assembly for the Honda Accord?
A: Disconnect the battery and drain the power steering fluid. Loosen lug nuts, raise the vehicle, and remove wheels. Under the dashboard, remove and mark the steering universal joint. Detach tie-rod ends and remove the heat shield. Disconnect the return hose and feed line anchors, and remove the lines from the steering gear. Remove the middle mounts and shock tower cross brace. Disconnect the EPS motor angle sensor and motor electrical connectors. Remove the mounting bolts on the left side of the steering gear. Lower the subframe with jacks and remove the right side mounting bolts. Remove the steering gear assembly through the left wheel opening. For installation, reverse the steps, ensuring proper torque on bolts and replacing loosened subframe bolts. Refill the Power Steering Pump, bleed the system, check for leaks, and adjust alignment if necessary. Reconnect the battery.