How do you remove and install the CKP sensor on Honda Odyssey?

For all models except 2008 and later with VCM, start by disconnecting the cable from the negative battery terminal, then remove the crankshaft pulley. For 2004 and earlier models, take out the dipstick and its tube, followed by the upper and lower timing belt covers. Disconnect the wiring from the sensor and remove it from the oil pump, noting that the CKP sensor electrical connector is located behind the right end of the engine, above the timing belt tensioner for 2007 and earlier models; detach the CKP sensor by removing the mounting bolt. Installation follows the reverse order of removal. For 2008 and later models with VCM, raise the vehicle and support it securely on jackstands, disconnect the cable from the negative battery terminal, and remove the cover from the CKP sensor located at the left lower rear of the engine. Disconnect the wiring from the sensor, remove the sensor, and replace the O-ring, with installation being the reverse of removal.

Genuine Honda Odyssey Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Crankshaft Position Sensors found

View related parts
Honda Odyssey Sensor Assembly, Crank
Part Number: 37500-R40-A01
$128.85 MSRP: $183.55
You Save: $54.70 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2017 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX, 5 Door SE, 5 Door Touring | KA 5AT, KA 6AT
View related parts
Honda Odyssey Sensor Assembly, Crank (1-2)
Part Number: 37500-RCA-A01
$352.91 MSRP: $502.72
You Save: $149.81 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2010 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door EXL-T, 5 Door LX | KA 5AT
View related parts
Honda Odyssey Sensor Assembly, Crank-Tdc
Part Number: 37840-P0A-A01
$440.23 MSRP: $635.25
You Save: $195.02 (31%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: 37840-PAA-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996-1998 Honda Odyssey | 5 Door EX, 5 Door LX (6 Seats), 5 Door LX (7 Seats) | KA 4AT
View related parts
Honda Odyssey Sensor Assembly, Crank
Part Number: 37500-5J6-A01
$105.77 MSRP: $153.28
You Save: $47.51 (31%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Odyssey | 5 Door ELITE (10AT), 5 Door EX, 5 Door EX (10AT), 5 Door EX-L, 5 Door EX-L (10AT), 5 Door LX, 5 Door LX (10AT), 5 Door Touring (10AT) | KA 9AT, KA XAT
View related parts
Honda Odyssey Sensor, Crank
Part Number: 37501-P8F-A01
$181.56 MSRP: $258.64
You Save: $77.08 (30%)
Product Specifications
- Other Name: Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1999-2004 Honda Odyssey | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door VAN | KA 4AT, KA 5AT

Honda Odyssey Crankshaft Position Sensor

Crankshaft Position Sensor is an electronic system device that is found in Honda Odyssey particularly for the detecting of the crankshaft position of the car. This information is then sent to the power train control module where the information is used to control the fuel injectors and the ignition timing in order to provide the engine with the most favorable performance. A faulty Crankshaft Position Sensor may cause starting problems or stalling of the car engine or maybe hard starting. In recent past year, Honda Odyssey has applied several kinds of Crankshaft Position Sensors which include inductive, Hall Effect, magnetoresistive, and optical sensor. Inductive sensors are of the passive type and Hall and magnetoresistive sensors can measure only DC fields. Optical sensors give high accuracy of detection at the same time being sensitive to fouling. The basic difference of these sensors main comprise of how they operate and how vulnerable or resistant they are to certain conditions within the Honda Odyssey.

In search of affordable OEM Honda Odyssey Crankshaft Position Sensor? Consider browsing through our extensive inventory of genuine Honda Odyssey Crankshaft Position Sensor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Odyssey Crankshaft Position Sensor Parts Questions & Experts Answers

Sensor Assembly, Crank (1-2)
37500-RCA-A01
Q: How do you remove and install the CKP sensor on Honda Odyssey?
A: For all models except 2008 and later with VCM, start by disconnecting the cable from the negative battery terminal, then remove the crankshaft pulley. For 2004 and earlier models, take out the dipstick and its tube, followed by the upper and lower timing belt covers. Disconnect the wiring from the sensor and remove it from the oil pump, noting that the CKP sensor electrical connector is located behind the right end of the engine, above the timing belt tensioner for 2007 and earlier models; detach the CKP sensor by removing the mounting bolt. Installation follows the reverse order of removal. For 2008 and later models with VCM, raise the vehicle and support it securely on jackstands, disconnect the cable from the negative battery terminal, and remove the cover from the CKP sensor located at the left lower rear of the engine. Disconnect the wiring from the sensor, remove the sensor, and replace the O-ring, with installation being the reverse of removal.