How do you remove and install the driveaxles and intermediate shaft on Honda Fit?

On automatic transaxle models, an intermediate shaft and support bearing is used on the right (passenger's) side. To remove the axle shafts, first loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel. Alternatively, the vehicle can remain on the ground while the hubcap or center cap is removed, followed by unstaking and loosening the axle shaft nut. Unstake the axle shaft/hub nut using a punch or narrow chisel, then unscrew the nut while preventing the hub from turning by having an assistant apply the brakes or using a prybar. Remove the under-vehicle splash shield and drain the transaxle fluid if necessary. Detach the control arm from the steering knuckle, then push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. If the axle shaft splines are frozen, tap the end with a soft-faced hammer or use a puller. Place a drain pan underneath the transaxle to catch any lubricant that may spill out. For manual transaxle vehicles, remove the right axle shaft heat shield bolts and heat shield. Use a prybar to carefully pry the inner CV joint out of the transaxle for the left axle shaft or the right axle shaft on manual transaxle models, then remove the axle shaft. For the right axle shaft on automatic transaxle models, use a drift and hammer to release the inner CV from the intermediate shaft. If reusing the old axle shaft, install a new retaining clip on the axle end before installation. The installation process is the reverse of removal, ensuring to push the axle shaft in sharply to seat the retaining ring. Reconnect the control arm to the steering knuckle, install a new axle shaft/hub nut, and tighten it to the specified torque while staking the collar into the groove. Refill the transaxle with the proper lubricant, install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts. For the intermediate shaft, remove the right-side axle shaft, drain the transaxle fluid, and remove the shift cable cover. If applicable, remove the heat shield, then slide the intermediate shaft straight out of the transaxle, taking care not to damage the oil seal. Replace the oil seal if necessary, and if the support bearing needs replacement, take the shaft to an automotive machine shop. Install a new retaining clip on the end of the shaft, then install the shaft by reversing the removal procedure and tightening the support bearing bracket bolts. Finally, install the wheel and lug nuts, lower the vehicle, and refill the transaxle with the proper fluid.

Genuine Honda Fit Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Axle Shafts found

View related parts
Honda Fit Shaft Assembly, R Drive
Part Number: 44305-T5R-A92
$189.26 MSRP: $269.60
You Save: $80.34 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-T5R-A91
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door Sport | KA 6MT
View related parts
Honda Fit Shaft Assembly, L Drive
Part Number: 44306-T5R-A92
$189.26 MSRP: $269.60
You Save: $80.34 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-T5R-A91
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door Sport | KA 6MT
View related parts
Honda Fit Shaft Assembly, R Drive
Part Number: 44305-T5R-A02
$189.26 MSRP: $269.60
You Save: $80.34 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-T5R-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA CVT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-SLN-L00
$601.82 MSRP: $868.44
You Save: $266.62 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaced by: 44306-SLN-305
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-SAA-E00
$716.55 MSRP: $1033.99
You Save: $317.44 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5MT
View related parts
Honda Fit Shaft Assembly, L Drive
Part Number: 44306-T5R-A02
$189.26 MSRP: $269.60
You Save: $80.34 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-T5R-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2015-2020 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX, 5 Door LX SE, 5 Door Sport | KA CVT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-TK6-A01
$567.45 MSRP: $818.83
You Save: $251.38 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-TK6-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-TK6-A01
$567.45 MSRP: $818.83
You Save: $251.38 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TK6-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-SLN-L00
$683.30 MSRP: $986.00
You Save: $302.70 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaced by: 44305-SLN-305
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-TK6-A11
$567.45 MSRP: $818.83
You Save: $251.38 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TK6-A10
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT
View related parts
Honda Fit Shaft Assembly, Half
Part Number: 44500-TF0-Y00
$366.57 MSRP: $522.18
You Save: $155.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT
View related parts
Honda Fit Shaft Assembly, Half
Part Number: 44500-SLN-L00
$306.40 MSRP: $436.46
You Save: $130.06 (30%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-SLN-A00
$663.64 MSRP: $937.35
You Save: $273.71 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Honda Fit | 5 Door Base, 5 Door Sport | KA 5MT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-TF0-N20
$567.42 MSRP: $818.78
You Save: $251.36 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TK6-A50, 44306-TK6-A60
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5MT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-TK6-A11
$567.45 MSRP: $818.83
You Save: $251.38 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-TK6-A10
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5AT
View related parts
Honda Fit Driveshaft Assembly, Driver Side
Part Number: 44306-T5R-000
$569.29 MSRP: $821.48
You Save: $252.19 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2017 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX | KA CVT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-TF0-N20
$582.92 MSRP: $841.15
You Save: $258.23 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaced by: 44305-TK6-316
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Honda Fit | 5 Door FIT, 5 Door Sport | KA 5MT
View related parts
Honda Fit Driveshaft Assembly, Passenger Side
Part Number: 44305-T5R-000
$678.59 MSRP: $979.20
You Save: $300.61 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2017 Honda Fit | 5 Door EX, 5 Door EX-L, 5 Door EX-LN, 5 Door LX | KA CVT

Honda Fit Axle Shaft

The Axle Shaft in Honda Fit vehicles is a very important sub-assembly that transfers the output power from the differential to the drive wheels to enable independent rotation, even though the wheels are joined by those shafts. This design increases the surface area for better grip especially at the corner of the car. The Honda Fit models replace halfshafts, that have splined shafts linked to both CV joints, this arrangement effectuates the alteration in power flow while taking into consideration the independent suspension system of the auto-mobile. For many years, this model of the Honda Fit has mostly used this halfshaft design, unlike a solid axle regular with trucks. Whereas solid axles bear loads and transmit loads, the halfshafts in Honda Fit vehicles are geared for efficiency and better ride comfort. There is always the need for periodic check-ups as a worn out CV joint or a damaged axle seal can lead to some problems to do with the performance of the vehicle which points towards the relevance of the Axle Shaft.

In search of affordable OEM Honda Fit Axle Shaft? Consider browsing through our extensive inventory of genuine Honda Fit Axle Shaft. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Fit Axle Shaft Parts Questions & Experts Answers

Driveshaft Assembly, Driver Side
44306-SAA-E00
Q: How do you remove and install the driveaxles and intermediate shaft on Honda Fit?
A: On automatic transaxle models, an intermediate shaft and support bearing is used on the right (passenger's) side. To remove the axle shafts, first loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel. Alternatively, the vehicle can remain on the ground while the hubcap or center cap is removed, followed by unstaking and loosening the axle shaft nut. Unstake the axle shaft/hub nut using a punch or narrow chisel, then unscrew the nut while preventing the hub from turning by having an assistant apply the brakes or using a prybar. Remove the under-vehicle splash shield and drain the transaxle fluid if necessary. Detach the control arm from the steering knuckle, then push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. If the axle shaft splines are frozen, tap the end with a soft-faced hammer or use a puller. Place a drain pan underneath the transaxle to catch any lubricant that may spill out. For manual transaxle vehicles, remove the right axle shaft heat shield bolts and heat shield. Use a prybar to carefully pry the inner CV joint out of the transaxle for the left axle shaft or the right axle shaft on manual transaxle models, then remove the axle shaft. For the right axle shaft on automatic transaxle models, use a drift and hammer to release the inner CV from the intermediate shaft. If reusing the old axle shaft, install a new retaining clip on the axle end before installation. The installation process is the reverse of removal, ensuring to push the axle shaft in sharply to seat the retaining ring. Reconnect the control arm to the steering knuckle, install a new axle shaft/hub nut, and tighten it to the specified torque while staking the collar into the groove. Refill the transaxle with the proper lubricant, install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts. For the intermediate shaft, remove the right-side axle shaft, drain the transaxle fluid, and remove the shift cable cover. If applicable, remove the heat shield, then slide the intermediate shaft straight out of the transaxle, taking care not to damage the oil seal. Replace the oil seal if necessary, and if the support bearing needs replacement, take the shaft to an automotive machine shop. Install a new retaining clip on the end of the shaft, then install the shaft by reversing the removal procedure and tightening the support bearing bracket bolts. Finally, install the wheel and lug nuts, lower the vehicle, and refill the transaxle with the proper fluid.

Related Honda Fit Parts

Browse by Year

2020 Axle Shaft 2019 Axle Shaft 2018 Axle Shaft 2017 Axle Shaft 2016 Axle Shaft 2015 Axle Shaft 2013 Axle Shaft 2012 Axle Shaft 2011 Axle Shaft 2010 Axle Shaft 2009 Axle Shaft 2008 Axle Shaft 2007 Axle Shaft