Other Name: Bearing, Front Wheel Bearing, Wheel Bearing
Position: Front
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2017-2022 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, Hybrid EX, Hybrid EX-L, Hybrid Touring, LX, Special Edition, Touring | KA CVT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2017-2022 Honda CR-V | 5 Door EX (AWD), 5 Door EX-L (AWD), 5 Door LX (AWD), 5 Door Touring (AWD), EX, EX-L, Hybrid EX, Hybrid EX-L, Hybrid Touring, LX, Special Edition, Touring | KA CVT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2007-2016 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD), 5 Door SE (AWD), 5 Door Touring (AWD) | KA 5AT, KA CVT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2017-2024 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, Hybrid EX, Hybrid EX-L, Hybrid Touring, LX, Special Edition, Touring | KA CVT
Warranty: This genuine part is guaranteed by Honda's
factory warranty.
Fits the following Vehicles:
2007-2016 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (4WD), 5 Door SE (AWD), 5 Door Touring (AWD) | KA 5AT, KA CVT
Q: How to remove and install a Wheel Hub on Honda CR-V?
A: Remove the Steering Knuckle. Using the proper adapter and press plate, press the hub out of the knuckle/wheel bearing with a hydraulic, from the back side to the front. Using a bearing splitter and the proper adapter, press the hub through the bearing inner race. Remove the screws and detach the disc splash shield from the knuckle. Remove the snap-ring from the backside of the knuckle. Using the proper adapter and press plate, press the bearing out of the steering knuckle with a hydraulic press, from the backside to the front. Clean the bore in the knuckle. Reverse the removal procedure to install the new bearing. Caution: Install the bearing with the ABS wheel speed sensor encoder (the brown side of the bearing) facing the inside of the knuckle. Note: Do not forget to reinstall the snap-ring before installing the hub. The hub and bearing must be fully seated back in the knuckle before installing the steering knuckle. Install the steering knuckle.