Other Name: Ignition Lock Cylinder; Ignition Switch, Steering Lock
$215.32MSRP: $306.71
You Save: $91.39 (30%)
Add to Cart
More Info
Fits the following Vehicles:
1996-2000 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door SI, 3 Door CX, 3 Door DX, 4 Door DX, 4 Door EX, 4 Door LX | KA 5MT, KL 5MT, KR 5MT, KW 5MT
2003-2005 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door LX, 3 Door SI, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX, 4 Door LX-CAR, 4 Door MX (Hybrid) | KA 4AT, KA 5MT, KA CVT, KL 5MT, KL CVT
2006-2011 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door LX-S, 4 Door SI | KA 5MT, KA 6MT
2016-2021 Honda Civic | 4 Door EX, 4 Door EX (Turbo), 4 Door EX-A, 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door SI, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo), 5 Door EX, 5 Door EX-L, 5 Door SE, 5 Door Sport, 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring) | KA 6MT, KA CVT, KL CVT
2014-2015 Honda Civic | 2 Door EX, 2 Door EX-L, 2 Door SI, 4 Door EX, 4 Door EX-L, 4 Door MX, 4 Door MX (Hybrid), 4 Door SI | KA 5MT, KA 6MT, KA CVT, KL CVT
2016-2020 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door LX (CVT), 2 Door SI, 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo) | KA 6MT, KA CVT, KL CVT
Other Name: Ignition Lock Cylinder; Ignition Switch, Steering Lock
$213.88MSRP: $304.67
You Save: $90.79 (30%)
More Info
Fits the following Vehicles:
1996-2000 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 3 Door CX, 3 Door DX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX | KA 4AT, KA CVT, KL 4AT, KL CVT
Less Info
| Page 1 of 9 |Next >
1-20 of 162 Results
Honda Civic Ignition Lock Cylinder Parts Questions & Answers
Q: How do you disconnect and replace the ignition switch and key lock cylinder on Honda Civic?
A: Disconnect the cable from the negative battery terminal and wait at least three minutes before proceeding. Remove the driver's dashboard panel assembly and the steering column covers. For the ignition switch (key type), disconnect the electrical connector from the ignition switch by pulling the release tab, then remove the ignition switch mounting screws and the switch itself. Installation is the reverse of removal, ensuring to reconnect the cable to the negative battery terminal and verify the ignition switch operates correctly in all positions. If replacing the Ignition Lock Cylinder, the immobilizer and transmitter must be reprogrammed using the factory scan tool at a dealer service department or qualified repair facility. Disconnect the negative battery terminal and wait at least three minutes before continuing. Remove the steering column covers and dashboard panels, then disconnect the ignition switch electrical connector along with the connectors for the Ignition Lock Cylinder, immobilizer control unit/receiver, and Ignition Lock Cylinder/key light. Remove the ignition switch and the immobilizer unit by disconnecting the immobilizer connector and carefully lifting the tabs. Center-punch the shear-head bolts securing the Ignition Lock Cylinder housing to the steering column, drill holes in the center of each bolt with a 3/16-inch drill bit, and unscrew them with a screw extractor. Remove the Ignition Lock Cylinder assembly from the steering column, verify the steering wheel lock mechanism functions correctly with the ignition key, and tighten the new shear-head bolts until the heads break off. For the ignition switch (push button start system), disconnect the negative battery terminal and wait at least three minutes before proceeding. Remove the driver's side dash vent trim, dash center pocket, audio/navigation unit, and lower dash trim panels, then remove the instrument cluster display trim panel and disconnect the electrical connector to the ignition push button switch. Turn the instrument cluster display trim cover and remove the screws securing the ignition push button switch to the trim cover, with installation being the reverse of removal.