How to remove and install a Clutch Master Cylinder on Honda Civic?

Remove the center cowl cover and the under cowl panel. Working under the dashboard, remove the cotter pin or spring clip from the master cylinder pushrod clevis. Pull out the clevis pin to disconnect the pushrod from the pedal. Unscrew the two clutch master cylinder retaining nuts. Use a syringe or other suitable method, to remove and properly dispose of the hydraulic fluid from the clutch master cylinder reservoir. Caution: Don't allow brake fluid to come into contact with the paint as it will damage the finish. Remove the air filter housing and air cleaner bracket. Release the clutch hydraulic line from the retaining clamp that secures it to the coolant line. On 1.8L models, remove the battery and battery tray, the brake fluid reservoir and ECM/PCM harness. The ECM/PCM connectors are labeled with symbols to identify their locations. Disconnect the steel clutch line from the fitting where it joins the flexible clutch hose. Have rags handy as some fluid will be lost as the line is removed. Cap or plug the ends of the line (orhose) to prevent fluid leakage and the entry of contaminants. Clamp a pair of locking pliers onto the clutch fluid feed hose, a couple of inches downstream of the reservoir. The pliers should be just tight enough to prevent fluid flow when the hose is disconnected. Remove the clutch master cylinder from the firewall with the hydraulic fluid reservoir and hydraulic lines still attached, then disconnect the clutch fluid feed hose and the hydraulic line at the cylinder. Again, have rags handy and cap or plug the ends of the lines (orhose) to prevent fluid leakage. Caution: Don't allow brake fluid to come into contact with the paint as it will damage the finish. Installation: Installation is the reverse of removal, noting the following points: Use a new gasket between the master cylinder and the firewall. Tighten the master cylinder mounting nuts. Install a new O-ring seal and retainer clip on the hydraulic line fitting at the master cylinder. Fill the clutch master cylinder reservoir with brake fluid conforming to DOT 3 specifications and bleed the clutch system.

Genuine Honda Civic Clutch Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Clutch Master Cylinders found

View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46925-TA0-A03
$160.90 MSRP: $229.20
You Save: $68.30 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaced by: 46925-TA0-305
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2015 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door LX-S, 4 Door SI | KA 5MT, KA 6MT
View related parts
Honda Civic Master Cylinder Assy., Clutch
Part Number: 46920-S7A-A05
$164.63 MSRP: $234.52
You Save: $69.89 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaces: 46920-S7A-A03, 46920-S7A-A01, 46920-S7A-A02, 46920-S7A-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda Civic | 3 Door SI | KA 5MT
View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46920-S5A-G07
$214.32 MSRP: $305.30
You Save: $90.98 (30%)
ADD TO CART
Product Specifications
- Other Name: M/Cyl Assembly, Clutch; Master Cylinder
- Replaces: 46920-S5A-G01, 46920-S5A-G03, 46920-S5A-G04, 46920-S5A-G02, 46920-S5A-G05, 46920-S5A-G06
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2001-2005 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door LX, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door LX, 4 Door MX (Hybrid) | KA 5MT, KL 5MT
View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46920-S04-A01
$168.14 MSRP: $239.51
You Save: $71.37 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996-2000 Honda Civic | 2 Door DX, 2 Door EX, 2 Door HX, 2 Door SI, 3 Door CX, 3 Door DX, 4 Door DX, 4 Door EX, 4 Door LX | KA 5MT, KL 5MT, KR 5MT, KW 5MT
View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46920-S7A-A04
$164.63 MSRP: $234.52
You Save: $69.89 (30%)
ADD TO CART
Product Specifications
- Other Name: M/Cyl Assembly, Clutch
- Replaced by: 46920-S7A-A05
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2005 Honda Civic | 3 Door SI | KA 5MT
View related parts
Honda Civic M/C Assembly-, Clutch
Part Number: 46925-TEA-A22
$159.51 MSRP: $227.22
You Save: $67.71 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaces: 46925-TEA-A21
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring) | KA 6MT
View related parts
Honda Civic M/C Assembly, Clutch
Part Number: 46925-TEA-A21
$159.51 MSRP: $227.22
You Save: $67.71 (30%)
ADD TO CART
Product Specifications
- Replaced by: 46925-TEA-A22
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2019 Honda Civic | 5 Door Type R, 5 Door Type R (Touring) | KA 6MT
View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46925-TGG-A01
$159.51 MSRP: $227.22
You Save: $67.71 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaces: 46925-TBA-A02, 46925-TBA-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door EX (Turbo/6MT), 2 Door LX (6MT), 2 Door SI, 2 Door Sport, 2 Door Sport (6MT), 4 Door EX (Turbo), 4 Door EX-T, 4 Door LX, 4 Door LX (6MT), 4 Door SI, 4 Door Sport, 4 Door Sport (6MT), 5 Door LX, 5 Door Sport | KA 6MT
View related parts
Honda Civic M/CYL ASSY-, CLUTCH
Part Number: 46920-3K0-H02
$60.68 MSRP: $85.70
You Save: $25.02 (30%)
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022-2023 Honda Civic | EX, EX-L, LX, Si, Sport, Sport Touring, Touring
View related parts
Honda Civic Master Cylinder Assembly, Clutch
Part Number: 46920-SR3-A01
Product Specifications
- Other Name: Master Cylinder
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1995 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-S, 3 Door CX, 3 Door DX, 3 Door SI, 3 Door VX, 4 Door DX, 4 Door EX, 4 Door LX | KA 5MT, KL 5MT
View related parts
Honda Civic M/C Assembly, Clutch
Part Number: 46925-TA0-A02
$160.90 MSRP: $229.20
You Save: $68.30 (30%)
Product Specifications
- Other Name: Master Cylinder
- Replaced by: 46925-TA0-305
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2015 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SI, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door LX-S, 4 Door SI | KA 5MT, KA 6MT

About Honda Civic Clutch Master Cylinder

A Honda Civic needs to be kept in good working condition in your vehicle. The online catalog we provide will get you through the ordering process safely and securely. All genuine Honda Clutch Master Cylinders from us are shipped directly from authorized Honda Dealer. If you want search for Honda Clutch Master Cylinder fast and easily, just come to Hondapartsnow.com to look for your parts.

Honda Civic Clutch Master Cylinder Parts Questions & Experts Answers

M/C Assembly, Clutch
46925-TA0-A02
Q: How to remove and install a Clutch Master Cylinder on Honda Civic?
A: Remove the center cowl cover and the under cowl panel. Working under the dashboard, remove the cotter pin or spring clip from the master cylinder pushrod clevis. Pull out the clevis pin to disconnect the pushrod from the pedal. Unscrew the two clutch master cylinder retaining nuts. Use a syringe or other suitable method, to remove and properly dispose of the hydraulic fluid from the clutch master cylinder reservoir. Caution: Don't allow brake fluid to come into contact with the paint as it will damage the finish. Remove the air filter housing and air cleaner bracket. Release the clutch hydraulic line from the retaining clamp that secures it to the coolant line. On 1.8L models, remove the battery and battery tray, the brake fluid reservoir and ECM/PCM harness. The ECM/PCM connectors are labeled with symbols to identify their locations. Disconnect the steel clutch line from the fitting where it joins the flexible clutch hose. Have rags handy as some fluid will be lost as the line is removed. Cap or plug the ends of the line (orhose) to prevent fluid leakage and the entry of contaminants. Clamp a pair of locking pliers onto the clutch fluid feed hose, a couple of inches downstream of the reservoir. The pliers should be just tight enough to prevent fluid flow when the hose is disconnected. Remove the clutch master cylinder from the firewall with the hydraulic fluid reservoir and hydraulic lines still attached, then disconnect the clutch fluid feed hose and the hydraulic line at the cylinder. Again, have rags handy and cap or plug the ends of the lines (orhose) to prevent fluid leakage. Caution: Don't allow brake fluid to come into contact with the paint as it will damage the finish. Installation: Installation is the reverse of removal, noting the following points: Use a new gasket between the master cylinder and the firewall. Tighten the master cylinder mounting nuts. Install a new O-ring seal and retainer clip on the hydraulic line fitting at the master cylinder. Fill the clutch master cylinder reservoir with brake fluid conforming to DOT 3 specifications and bleed the clutch system.

Related Honda Civic Parts

Browse by Year