How to remove and replace a driveaxle on the Honda Accord?

Loosen the front wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Unstake the axle shaft/hub nut with a punch or chisel. Loosen the axle shaft/hub nut with a large socket and breaker bar, then remove the axle shaft/hub nut from the axle and discard it. Remove the damper fork-to-lower control arm bolt, then separate the lower control arm from the steering knuckle. Swing the knuckle/hub assembly out (away from the vehicle) until the end of the axle shaft is free of the hub. If the axle shaft splines stick in the hub, tap on the end of the axle shaft with a plastic hammer. Support the outer end of the axle shaft with a piece of wire to avoid unnecessary strain on the inner CV joint. Pry the inner CV joint out of the transaxle or, on models so equipped, the intermediate shaft, using a large screwdriver or prybar. Support the CV joints and carefully remove the axle shaft from the vehicle. To prevent damage to the intermediate shaft seal or the differential seal, hold the inner CV joint horizontal until the axle shaft is clear of the intermediate shaft or transaxle. Place a drain pan under the inner CV joint to catch any fluid from the transaxle that might drain out when the axle shaft is removed. Pry the old spring clip from the inner end of the axle shaft and install a new one. Lubricate the differential or intermediate shaft seal with multi-purpose grease and raise the axle shaft into position while supporting the CV joints. Insert the splined end of the inner CV joint into the differential side gear or intermediate shaft and make sure the spring clip locks in its groove. Apply a light coat of multi-purpose grease to the outer CV joint splines, pull out on the strut/steering knuckle assembly and install the stub axle into the hub. Insert the stud of the steering knuckle balljoint into the lower control arm and tighten the nut. Be sure to use a new cotter pin. Install the damper fork. Install the axle shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it until you've lowered the vehicle to the ground. Grasp the inner CV joint housing (not the axle shaft) and pull out to make sure the axle shaft has seated securely in the transaxle.

Genuine Honda Accord Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

213 Axle Shafts found

View related parts
Honda Accord Shaft Assembly, Half
Part Number: 44500-T2A-A00
$536.97 MSRP: $774.85
You Save: $237.88 (31%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2017 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX-S, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door SE, 4 Door Sport | KA CVT, KL CVT
View related parts
Honda Accord Shaft Assembly, Half
Part Number: 44500-T4P-J00
$208.52 MSRP: $297.03
You Save: $88.51 (30%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport, 4 Door Touring, EX-L, LX, Sport, Sport SE | KA CVT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-TVA-A51
$246.45 MSRP: $351.06
You Save: $104.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport, 4 Door Touring, EX-L, LX, Sport, Sport SE | KA CVT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TVA-A51
$246.45 MSRP: $351.06
You Save: $104.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport, 4 Door Touring, EX-L, LX, Sport, Sport SE | KA CVT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TVC-A52
$246.45 MSRP: $351.06
You Save: $104.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-TVC-A51
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door (2.0 Sport), 4 Door (2.0 Touring), 4 Door EX-L (2.0), Sport, Touring | KA XAT
View related parts
Honda Accord Shaft Assembly, Half
Part Number: 44500-TA0-A00
$562.99 MSRP: $812.40
You Save: $249.41 (31%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door LX-S, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TA1-A01
$516.98 MSRP: $746.00
You Save: $229.02 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-TA1-A000, 44305-TA1-A00, 44305-TA1-A00RM
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX-L V6, 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-TA1-A01
$516.98 MSRP: $746.00
You Save: $229.02 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TA1-A00RM, 44306-TA1-A00, 44306-TA1-A000
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX-L V6, 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-TA0-A01
$524.04 MSRP: $756.18
You Save: $232.14 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TA0-A00RM, 44306-TA0-A000, 44306-TA0-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TA0-A00
$522.87 MSRP: $754.50
You Save: $231.63 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaced by: 44305-TA0-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TA0-A50
$695.28 MSRP: $1003.29
You Save: $308.01 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaced by: 44305-TA0-A53
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door LX-S, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Shaft Assembly, Half
Part Number: 44500-TA1-A00
$433.03 MSRP: $624.87
You Save: $191.84 (31%)
ADD TO CART
Product Specifications
- Other Name: Intermediate Shaft; Intermed Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX-L V6, 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV) | KA 5AT, KL 5AT
View related parts
Honda Accord Shaft Assembly, Half
Part Number: 44500-TBF-A00
$339.34 MSRP: $483.38
You Save: $144.04 (30%)
ADD TO CART
Product Specifications
- Other Name: Intermed Shaft, Intermediate Shaft
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2020 Honda Accord | 4 Door Sport | KA 6MT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-TVC-A52
$246.45 MSRP: $351.06
You Save: $104.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-TVC-A51
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2022 Honda Accord | 4 Door (2.0 Sport), 4 Door (2.0 Touring), 4 Door EX-L (2.0), Sport, Touring | KA XAT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-TE1-A00
$331.12 MSRP: $471.69
You Save: $140.57 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaced by: 44306-TE1-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX-L V6 | KA 6MT, KL 6MT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-SDC-A00
$641.22 MSRP: $925.28
You Save: $284.06 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 44305-SDA-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2007 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door EX-SUL, 2 Door LX, 2 Door LX-SUL, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door SE, 4 Door VP | KA 5AT, KL 5AT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-T3M-A00
$192.32 MSRP: $273.96
You Save: $81.64 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2014 Honda Accord | 2 Door EX-L V6 | KA 6MT, KL 6MT
View related parts
Honda Accord Driveshaft Assembly, Driver Side
Part Number: 44306-SDC-A01
$596.29 MSRP: $860.45
You Save: $264.16 (31%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Replaces: 44306-SDA-A00, 44306-SDA-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2007 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door EX-SUL, 2 Door LX, 2 Door LX-SUL, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door SE, 4 Door VP | KA 5AT, KL 5AT
View related parts
Honda Accord Shaft Assembly, R Drive
Part Number: 44305-T2B-A00
$236.84 MSRP: $337.38
You Save: $100.54 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2014 Honda Accord | 2 Door EX-L V6, 4 Door EX-L V6, 4 Door Touring (V6) | KA 6AT, KL 6AT
View related parts
Honda Accord Driveshaft Assembly, Passenger Side
Part Number: 44305-TWA-A01
$246.45 MSRP: $351.06
You Save: $104.61 (30%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022 Honda Accord | Hybrid, Hybrid EX-L, Hybrid Sport, Hybrid Touring

| Page 1 of 11 |Next >

1-20 of 213 Results

Honda Accord Axle Shaft

This is a part of Honda Accord vehicles that power the drive wheels through the differential and enables independent rotation for better grip. Acting as a spine to the wheel that rotates on it, the Axle Shaft bears the weight of the car, transmits the torque to operate the wheel and helps in keeping the wheels in place. It is also worth mentioning that there are diversified kinds of Axle Shafts: live axles for the torque transfer and split axles for the independent suspension. Constructed of Chrome-Molybdenum or carbon steel, Axle Shafts are relatively important in the running of vehicles and other related machinery.

In search of affordable OEM Honda Accord Axle Shaft? Consider browsing through our extensive inventory of genuine Honda Accord Axle Shaft. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Accord Axle Shaft Parts Questions & Experts Answers

Driveshaft Assembly, Passenger Side
44305-SDC-A51
Q: How to remove and replace a driveaxle on the Honda Accord?
A: Loosen the front wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Unstake the axle shaft/hub nut with a punch or chisel. Loosen the axle shaft/hub nut with a large socket and breaker bar, then remove the axle shaft/hub nut from the axle and discard it. Remove the damper fork-to-lower control arm bolt, then separate the lower control arm from the steering knuckle. Swing the knuckle/hub assembly out (away from the vehicle) until the end of the axle shaft is free of the hub. If the axle shaft splines stick in the hub, tap on the end of the axle shaft with a plastic hammer. Support the outer end of the axle shaft with a piece of wire to avoid unnecessary strain on the inner CV joint. Pry the inner CV joint out of the transaxle or, on models so equipped, the intermediate shaft, using a large screwdriver or prybar. Support the CV joints and carefully remove the axle shaft from the vehicle. To prevent damage to the intermediate shaft seal or the differential seal, hold the inner CV joint horizontal until the axle shaft is clear of the intermediate shaft or transaxle. Place a drain pan under the inner CV joint to catch any fluid from the transaxle that might drain out when the axle shaft is removed. Pry the old spring clip from the inner end of the axle shaft and install a new one. Lubricate the differential or intermediate shaft seal with multi-purpose grease and raise the axle shaft into position while supporting the CV joints. Insert the splined end of the inner CV joint into the differential side gear or intermediate shaft and make sure the spring clip locks in its groove. Apply a light coat of multi-purpose grease to the outer CV joint splines, pull out on the strut/steering knuckle assembly and install the stub axle into the hub. Insert the stud of the steering knuckle balljoint into the lower control arm and tighten the nut. Be sure to use a new cotter pin. Install the damper fork. Install the axle shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it until you've lowered the vehicle to the ground. Grasp the inner CV joint housing (not the axle shaft) and pull out to make sure the axle shaft has seated securely in the transaxle.