How to replace the key lock cylinder and ignition switch assembly on Honda Pilot?

A one-piece assembly is The Ignition Lock Cylinder and ignition switch assembly, which is also referred to as the "steering lock". If either the Ignition Lock Cylinder or the ignition switch fails, replace the assembly. Unplug negative battery terminal using cable followed by waiting for not less than three minutes. It is necessary to remove knee bolster and upper and lower steering column covers. Turn over driver's side fuse and relay box in order to reach panel backside. Trace electrical harness down from Ignition Lock Cylinder/ignition switch assembly towards driver's side fuse and relay box, detach any harness clips, then disconnect ignition switch electrical connector from fuse and relay box. Detach clip of driver's side airbag wiring harness from bracket on Ignition Lock Cylinder/ignition switch assembly. Disconnect small electrical connector from Ignition Lock Cylinder/ignition switch assembly. Center-punch two shear-head bolts that secure mounting clamp for Ignition Lock Cylinder/ignition switch assembly, next drill out center of each bolt removing bolts with use of screw extractor. Another possible way might be using a hammer chisel to knock off bolts in a counterclockwise direction. Remove bracket then separate lock cylinder/ignition switch assembly at steering column. Reverse steps for installation process after completing removal process hereinabove outlined in steps 1 through 14. Tighten new shear-head bolts until heads break off completely. After finishing reconnect cable back onto negative battery terminal again Verify proper functioning of Ignition Lock Cylinder/ignition switch assembly.

Genuine Honda Pilot Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Ignition Switches found

View related parts
Honda Pilot Switch Assembly
Part Number: 35881-TG7-A04
$77.57 MSRP: $109.56
You Save: $31.99 (30%)
ADD TO CART
Product Specifications
- Other Name: Power Switch, Start Button
- Replaces: 35881-TG7-A01, 35881-TG7-A03, 35881-TG7-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2022 Honda Pilot | 5 Door Black (AWD), 5 Door ELITE (AWD), 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), Black Edition, EX-L, Elite, Special Edition, Sport, Touring, TrailSport | KA 6AT, KA 9AT
View related parts
Honda Pilot Switch Assembly, Engine Start & Stop
Part Number: 35881-TG7-A03
$77.57 MSRP: $109.56
You Save: $31.99 (30%)
ADD TO CART
Product Specifications
- Replaced by: 35881-TG7-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2020 Honda Pilot | 5 Door Black (AWD), 5 Door ELITE (AWD), 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD) | KA 6AT, KA 9AT
View related parts
Honda Pilot Switch, Steering
Part Number: 35130-SZA-901
$55.11 MSRP: $77.84
You Save: $22.73 (30%)
ADD TO CART
Product Specifications
- Other Name: Ignition Switch
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2015 Honda Pilot | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX 4.4 (4WD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX 4.2 (4WD), 5 Door SE (2WD), 5 Door SE (4WD), 5 Door Touring (2WD), 5 Door Touring (4WD) | KA 5AT
View related parts
Honda Pilot Switch, Steering
Part Number: 35130-S9V-A12
$69.99 MSRP: $98.85
You Save: $28.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Ignition Switch
- Replaces: 35130-S9V-A11
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2005-2008 Honda Pilot | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX-L, 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door EX-SE (2WD), 5 Door EX-SE (4WD), 5 Door LX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door LX-VP (2WD), 5 Door LX-VP (4WD) | KA 5AT
View related parts
Honda Pilot Switch, Steering
Part Number: 35130-S9V-A01
$108.90 MSRP: $153.81
You Save: $44.91 (30%)
ADD TO CART
Product Specifications
- Other Name: Ignition Switch
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2004 Honda Pilot | 5 Door EX, 5 Door EX-L, 5 Door LX | KA 5AT, KL 5AT
View related parts
Honda Pilot SWITCH ASSY
Part Number: 35881-TZA-A01
$24.72 MSRP: $34.92
You Save: $10.20 (30%)
ADD TO CART
Product Specifications
- Other Name: Power Switch, Start Button
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2023-2024 Honda Pilot | Elite, EX-L, Sport, Touring, TrailSport

About Honda Pilot Ignition Switch

A Honda Pilot needs to be kept in good working condition in your vehicle. The online catalog we provide will get you through the ordering process safely and securely. All genuine Honda Ignition Switches from us are shipped directly from authorized Honda Dealer. If you want search for Honda Ignition Switch fast and easily, just come to Hondapartsnow.com to look for your parts.

Honda Pilot Ignition Switch Parts Questions & Experts Answers

Switch, Steering
35130-S9V-A12
Q: How to replace the key lock cylinder and ignition switch assembly on Honda Pilot?
A: A one-piece assembly is The Ignition Lock Cylinder and ignition switch assembly, which is also referred to as the "steering lock". If either the Ignition Lock Cylinder or the ignition switch fails, replace the assembly. Unplug negative battery terminal using cable followed by waiting for not less than three minutes. It is necessary to remove knee bolster and upper and lower steering column covers. Turn over driver's side fuse and relay box in order to reach panel backside. Trace electrical harness down from Ignition Lock Cylinder/ignition switch assembly towards driver's side fuse and relay box, detach any harness clips, then disconnect ignition switch electrical connector from fuse and relay box. Detach clip of driver's side airbag wiring harness from bracket on Ignition Lock Cylinder/ignition switch assembly. Disconnect small electrical connector from Ignition Lock Cylinder/ignition switch assembly. Center-punch two shear-head bolts that secure mounting clamp for Ignition Lock Cylinder/ignition switch assembly, next drill out center of each bolt removing bolts with use of screw extractor. Another possible way might be using a hammer chisel to knock off bolts in a counterclockwise direction. Remove bracket then separate lock cylinder/ignition switch assembly at steering column. Reverse steps for installation process after completing removal process hereinabove outlined in steps 1 through 14. Tighten new shear-head bolts until heads break off completely. After finishing reconnect cable back onto negative battery terminal again Verify proper functioning of Ignition Lock Cylinder/ignition switch assembly.