Contact Us Live Chat or 1-888-984-2011
My Garage
My Account
Cart

Genuine Honda Passport Tie Rod End

Steering Rod End
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Tie Rod Ends found

  • Honda Passport Tie Rod End - 53540-TZ5-A01
    Diagram for Honda Passport Tie Rod End - 53540-TZ5-A01
    View related parts

    Honda Passport End, Passenger Side Tie Rod

    Part Number: 53540-TZ5-A01
    $44.86 MSRP: $63.37
    You Save: $18.51 (30%)
    ADD TO CART
    Product Specifications
    • Other Name: Outer Tie Rod
    • Position: Passenger Side
    • Warranty: This genuine part is guaranteed by Honda's factory warranty.
    Fits the following Vehicles:
    • 2019-2023 Honda Passport | 5 Door ELITE (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door Sport (2WD), 5 Door Sport (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX-L, Elite, Sport, Touring, TrailSport | KA 9AT
  • Honda Passport Tie Rod End - 53560-TZ5-A01
    Diagram for Honda Passport Tie Rod End - 53560-TZ5-A01
    View related parts

    Honda Passport End, Driver Side Tie Rod

    Part Number: 53560-TZ5-A01
    $44.86 MSRP: $63.37
    You Save: $18.51 (30%)
    ADD TO CART
    Product Specifications
    • Other Name: Outer Tie Rod
    • Position: Driver Side
    • Warranty: This genuine part is guaranteed by Honda's factory warranty.
    Fits the following Vehicles:
    • 2019-2023 Honda Passport | 5 Door ELITE (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door Sport (2WD), 5 Door Sport (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX-L, Elite, Sport, Touring, TrailSport | KA 9AT
  • Honda Passport Tie Rod End - 8-97160-395-0
    Diagram for Honda Passport Tie Rod End - 8-97160-395-0
    View related parts

    Honda Passport Rod End Assembly (Outer)

    Part Number: 8-97160-395-0
    $59.19 MSRP: $96.98
    You Save: $37.79 (39%)
    ADD TO CART
    Product Specifications
    • Position: Outer
    • Warranty: This genuine part is guaranteed by Honda's factory warranty.
    Fits the following Vehicles:
    • 1998-2002 Honda Passport | 4 Door 2EX, 4 Door 2EX-L, 4 Door 2LX, 4 Door 4EX, 4 Door 4EX-L, 4 Door 4LX, 4 Door 4LX-W | KA 4AT, KA 5MT, KL 4AT, KL 5MT
  • Honda Passport Tie Rod End - 8-97170-450-0
    Diagram for Honda Passport Tie Rod End - 8-97170-450-0
    View related parts

    Honda Passport Rod End Assembly (Outer)

    Part Number: 8-97170-450-0
    $69.60 MSRP: $114.03
    You Save: $44.43 (39%)
    ADD TO CART
    Product Specifications
    • Other Name: Outer Tie Rod
    • Position: Outer
    • Warranty: This genuine part is guaranteed by Honda's factory warranty.
    Fits the following Vehicles:
    • 1998-2002 Honda Passport | 4 Door 2EX, 4 Door 2EX-L, 4 Door 2LX, 4 Door 4EX, 4 Door 4EX-L, 4 Door 4LX, 4 Door 4LX-W | KA 4AT, KA 5MT, KL 4AT, KL 5MT

Honda Passport Tie Rod End Parts Questions & Experts Answers

  • Q: How to remove and install Center Link and Tie Rod End on Honda Passport?
    A: Any process of removing and installing the steering linkage requires the use of the front end of the automobile which must be lifted and supported on jackstuds. Before the removal of any steering linkage take a Ball Joint separator which can be screw puller type or the wedge type although the latter may damage the ball joint seals. It is also possible to free a balljoint taper pin by putting a suitable hammer against each resultant face of the eye; it is however usually cramped. This kind of means that after fitting any of the steering linkage parts be sure to have the front wheel alignment at a professional alignment shop. For the 1989 through 1997 models remove the outer jam nut and paint the relationship between the outer tie-rod end and the tie-rod shaft white. Ip out cotter pin and castle nut on the ball joint stud and then use small puller to remove the outer tie rod end from the steering knuckle arm. If it is necessary to replace the inner tie-rod end balljoint then it should be disconnected from the central link by unscrewing the jam nut with notice of threads, pulling off the cotter pin, unscrewing the castle nut and using a small puller. Before tightening it to fit a new tie-rod end, one fits it onto the tie-rod until it gets up to the mark before slightly tightening the jam nut to meet the rod end. Align the tie-rod ends perpendicular to each other and then fix the same with the jam nuts. The rest of the installation is the reveres of removal to check that the castle nuts have been tightened to their required torque. For the Pitman arm remove the nut which holds it to the steering gear sector shaft, mark the Pitman arm and the shaft during refitting so that they will align correctly, use a puller to free it from the splines of the shaft. Loosen and take off the cotter pin and the castle nut that joins the Pitman arm to the center link by means of a puller. Disassembly is the reverse of installation and requires the use of a wrench to loosen the nuts to the required torque and replacing a worn cotter pin with a new one. For the idler arm remove the cotter pin and loosen the castle nut, for the ball joint stud fit a puller and unbolt the idler arm from the frame. Disconnect the tie-rod ends, Pitman arm, and idler arm from the center link; the procedure for this is the same for removal and installation with the requirement that all the nuts should be tightened to the torque. For the steering damper, unscrew the cotter pin/nut/washer at the bolt connecting it to the center link and then the attachment to the cross member or the idler arm bracket and then pulling off the steering damper form the vehicle, while to replace it reverse the procedure. On all 1998 and newer models, use a wrench to take off the jam nut and put a marker to denote the position of the outer tie-rod end with regard to the tie-rod and take off the castle nut on the balljoint stud and then use a small puller to remove the outer tie-rod end from the steering knucle arm. When fitting a new tie-rod end, thread it on to the tie-rod up to the arrow, then screw on the jam nut until it engages the rod end but do not over tighten on the rod end. Place the stud of the tie-rod end balljoint firmly to the hole provided in the steering knuckle arm and tighten the nut to the recommended tightness.

Related Honda Passport Parts