×
- Hello
- Login or Register
- Quick Links
- Live Chat
- Track Order
- Parts Availability
- RMA
- Help Center
- Contact Us
- Shop for
- Honda Parts
- Honda Accessories
My Garage
My Account
Cart
Genuine Honda Crosstour Fuel Level Sensor
Gas Gauge Sensor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Fuel Level Sensors found
Honda Crosstour Fuel Level Sensor
The Fuel Level Sensor is a critical part of the Honda Crosstour vehicle since it continually calculates the level of fuel in the tank to help the driver. Such electronic sensors are made in a way that they can be highly efficient even in high-temperature conditions, and still, they would require low power and would provide very prompt and accurate results. Normally mounted in the fuel tank, the sensor is made up of part like float, actuating rod, and resistor all of which play a role of sending signals to the fuel gauge. It is suggested to bring your car to a professional for servicing in case there's a problem with the fuel level sensor in order to have an accurate measurement of the fuel that is left and be notified on any replenishment that is required.
In search of affordable OEM Honda Crosstour Fuel Level Sensor? Consider browsing through our extensive inventory of genuine Honda Crosstour Fuel Level Sensor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.
Honda Crosstour Fuel Level Sensor Parts Questions & Experts Answers
- Q: How to remove a Fuel Pump/Fuel Gauge Sending Unit on Honda Crosstour?A:Relieve the system fuel pressure, then remove the fuel filler neck cap to relieve any pressure inside the fuel tank. Disconnect the cable from the negative battery terminal, remove the fuel pump/Fuel Level Sensor from the fuel tank and place it on a clean workbench. Disconnect the electrical connector for the Fuel Level Sensor, remove the Fuel Level Sensor from the fuel pump assembly, disconnect the fuel pump electrical connector and ground wire, remove the fuel pump retainer from the fuel pump housing, remove the rubber insulator from the fuel pump, remove the fuel strainer from the inlet end of the fuel pump, remove the fuel pump from the pump housing. If you want to replace the fuel filter, wash the fuel inlet strainer thoroughly in clean solvent, dry it off and inspect it for tears, cracks, clogging any other damage. If the strainer is damaged or worn, replace it, be sure to use a new retaining washer when installing the strainer. Before installing the fuel pump access cover, be sure to connect the cable to the negative battery terminal, start the engine and check for fuel leaks at the pump fuel line connection. If there are no leaks, install the access cover and the trunk carpet.
- Q: How Do I Replace the Fuel Pump/Fuel Gauge Sending Unit on Honda Crosstour?A:Relieve the fuel system pressure and remove the fuel filler neck cap to relieve any pressure inside the fuel tank, then disconnect the cable from the negative battery terminal and remove the carpeting from the floor of the trunk. Remove the fuel pump access cover screws and access cover, disconnect the electrical connector from the fuel pump/Fuel Level Sensor, disconnect the quick-connect fitting for the fuel supply line, and on non-SULEV models, remove the fuel pump/Fuel Level Sensor locknut. On SULEV models, remove the six fuel pump retaining nuts. Carefully angle the fuel pump/Fuel Level Sensor out of the tank to protect the float arm and float from damage, inspect the seal for cracks, tears and deterioration, and if it's damaged, replace it. Install a new gasket in the hole before installing the fuel pump/Fuel Level Sensor in the fuel tank, and when installing the fuel pump/Fuel Level Sensor on a non-SULEV model, make sure that the index mark on top of the fuel pump/Fuel Level Sensor is pointing between the two marks on the edge of the hole. When installing the mounting flange on a SULEV model or on a V6 model, make sure that the three asymmetrically-located notches in the mounting flange are aligned with their corresponding lugs on top of the pump assembly. Before reconnecting the fuel supply line quick-connect fitting, be sure to replace the 0-ring inside the fitting, and when installing the fuel pump/Fuel Level Sensor on an SULEV model, be sure to tighten the retaining nuts to the torque. Installation is otherwise the reverse of removal.
