How to remove and install the door latch,Lock Cylinder and handle assembly on Honda CR-V?

Wear gloves when working inside the door openings to protect against cuts from sharp metal edges. All door lock rods are attached by plastic clips, which can be removed by unsnapping the portion that clips around the connecting rod and then pulling the rod out of its locating hole. On models with power door locks, disconnect the electrical connectors at the latch. To access the door latch, raise the window, then remove the door trim panel and water shield. Pry the rear window guide track lining out of the rear guide track, remove the single bolt securing the rear window guide track, and take the guide track out of the door. Remove the release cables from the door cable clips and the three screws securing the door latch to the door, then slide the latch downward to release the outside latch handle actuator rod. Open the latch protector door on the latch and disconnect the cables from the latch assembly before removing the latch. For the outside handle and door lock cylinder assembly, raise the window and remove the door trim panel and water shield. From the rear edge of the door, remove the plastic protector cap that hides the lock cylinder bolt, then pull the door lock cylinder straight away from the door handle. Release the clip securing the door latch actuator rod to the outside door handle from inside the door, then remove the outside handle retaining fastener. Pull the rear section of the door handle back to release it, pivot the rear section away from the door to free the front section, and remove the handle. For the inside handle, remove the door panel trim, pull the inside door handle to the rear to release the retaining hooks, and remove the cable from the inside door handle before taking out the handle. Installation is the reverse of removal for all components.

Genuine Honda CR-V Door Lock Cylinder

Door Lock Cylinder Tumbler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Door Lock Cylinders found

View related parts
Honda CR-V Cylinder, Driver Side Door
Part Number: 04921-TLA-A01
$55.28 MSRP: $78.08
You Save: $22.80 (30%)
ADD TO CART
Product Specifications
- Other Name: Cylinder & Key, Lock Cylinder
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2022 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD), EX, EX-L, Hybrid EX, Hybrid EX-L, Hybrid Touring, LX, Special Edition, Touring | KA CVT
View related parts
Honda CR-V Cylinder, L Door
Part Number: 72185-T0A-A01
$62.37 MSRP: $88.10
You Save: $25.73 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012-2016 Honda CR-V | 5 Door EX (2WD), 5 Door EX (AWD), 5 Door EX-L (2WD), 5 Door EX-L (AWD), 5 Door LX (2WD), 5 Door LX (AWD), 5 Door SE (2WD), 5 Door SE (AWD), 5 Door Touring (2WD), 5 Door Touring (AWD) | KA 5AT, KA CVT
View related parts
Honda CR-V Cylinder, Driver Side Door
Part Number: 72185-S9A-013
$64.04 MSRP: $90.44
You Save: $26.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Driver Side
- Replaces: 72185-S9A-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2006 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Cylinder, Driver Side Door
Part Number: 72185-SWA-A01
$97.66 MSRP: $137.93
You Save: $40.27 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock & Cylinder; Lock Cylinder
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2007-2011 Honda CR-V | 5 Door EX (2WD), 5 Door EX (4WD), 5 Door EX-L (2WD), 5 Door EX-L (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE (2WD), 5 Door SE (4WD) | KA 5AT
View related parts
Honda CR-V Cylinder, Driver Side Door
Part Number: 72146-S04-003
$47.37 MSRP: $66.90
You Save: $19.53 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda CR-V Cylinder, Passenger Side Door
Part Number: 72145-S9A-013
$64.04 MSRP: $90.44
You Save: $26.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Passenger Side
- Replaces: 72145-S9A-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2006 Honda CR-V | 5 Door EX, 5 Door EX (2WD), 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5AT, KA 5MT
View related parts
Honda CR-V Cylinder, Passenger Side Door
Part Number: 72145-S04-003
$47.28 MSRP: $66.78
You Save: $19.50 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda CR-V | 5 Door EX, 5 Door LX (2WD), 5 Door LX (4WD), 5 Door SE | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda CR-V Cylinder, Passenger Side Door
Part Number: 72145-S9A-003
$64.04 MSRP: $90.44
You Save: $26.40 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder; Cylinder & Key
- Position: Passenger Side
- Replaced by: 72145-S9A-013
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2002-2003 Honda CR-V | 5 Door EX (4WD), 5 Door LX (2WD), 5 Door LX (4WD) | KA 4AT, KA 5MT
View related parts
Honda CR-V CYLINDER, L- DOOR
Part Number: 04921-3A0-A11
$52.97 MSRP: $74.81
You Save: $21.84 (30%)
ADD TO CART
Product Specifications
- Other Name: Cylinder & Key, Lock Cylinder
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2023-2024 Honda CR-V | EX, EX-L, Hybrid Sport, Hybrid Sport Touring, Hybrid Sport-L, LX

Honda CR-V Door Lock Cylinder

The Door Lock Cylinder in Honda CR-V autos is an important part installed in the front doors which has the capacity to lock or unlock the doors with the aid of the car key. This mechanism makes it possible for the user to have easy access to the interior part of the vehicle while at the same time making it hard for an unauthorized person to access such a vehicle. In the long run, its frequent use may result to wear whereby the doors cannot easily be locked or unlocked and at one point the key may get stuck or fail to turn. Unlike many other contemporary cars, the Honda CR-V has not dumped the ever-relevant door lock cylinders. Therefore, it is important to perform periodic maintenance and replacement of the Door Lock Cylinder in Honda CR-V so as to realize the maximum functionality coupled with security.

In search of affordable OEM Honda CR-V Door Lock Cylinder? Consider browsing through our extensive inventory of genuine Honda CR-V Door Lock Cylinder. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda CR-V Door Lock Cylinder Parts Questions & Experts Answers

Cylinder, L Door
72185-T0A-A01
Q: How to remove and install the door latch,Lock Cylinder and handle assembly on Honda CR-V?
A: Wear gloves when working inside the door openings to protect against cuts from sharp metal edges. All door lock rods are attached by plastic clips, which can be removed by unsnapping the portion that clips around the connecting rod and then pulling the rod out of its locating hole. On models with power door locks, disconnect the electrical connectors at the latch. To access the door latch, raise the window, then remove the door trim panel and water shield. Pry the rear window guide track lining out of the rear guide track, remove the single bolt securing the rear window guide track, and take the guide track out of the door. Remove the release cables from the door cable clips and the three screws securing the door latch to the door, then slide the latch downward to release the outside latch handle actuator rod. Open the latch protector door on the latch and disconnect the cables from the latch assembly before removing the latch. For the outside handle and door lock cylinder assembly, raise the window and remove the door trim panel and water shield. From the rear edge of the door, remove the plastic protector cap that hides the lock cylinder bolt, then pull the door lock cylinder straight away from the door handle. Release the clip securing the door latch actuator rod to the outside door handle from inside the door, then remove the outside handle retaining fastener. Pull the rear section of the door handle back to release it, pivot the rear section away from the door to free the front section, and remove the handle. For the inside handle, remove the door panel trim, pull the inside door handle to the rear to release the retaining hooks, and remove the cable from the inside door handle before taking out the handle. Installation is the reverse of removal for all components.