How should the trunk lid be removed and installed safely and correctly on Honda Civic?

The trunk lid is heavy and somewhat awkward to remove and install, so at least two people should perform this procedure. To begin, open the trunk lid and cover the edges of the trunk compartment with pads or cloths to protect the painted surfaces. Disconnect any cables or wire harness connectors attached to the trunk lid that would interfere with removal. If equipped, remove the hinge trim cover and make alignment marks around the hinge by drawing around it and the bolts with a marking pen before loosening the bolts to ensure proper alignment when reinstalling. While an assistant supports the trunk lid, remove the lid-to-hinge bolts on both sides and lift it off. For installation, follow the reverse of the removal process, ensuring to align the lid-to-hinge bolts with the marks made earlier. For adjustment, fore-and-aft and side-to-side alignment of the trunk lid can be achieved by moving it in relation to the hinge after loosening the bolts or nuts. Scribe a line around the hinge plate to determine the amount of movement, then loosen the bolts and adjust the trunk lid into the correct alignment, tightening the hinge bolts or nuts afterward to check the alignment. If necessary, the entire trunk lid striker assembly can be adjusted up and down as well as from side to side by loosening two bolts to reposition the striker, marking its location for reference. Scribe a line around the striker assembly for guidance, then reposition as needed and retighten the mounting bolts. Periodically lubricate the trunk lid latch assembly and hinges with white lithium-base grease to prevent sticking and wear. Finally, adjust the height of the trunk lid in relation to the body by screwing the rubber bumpers in or out.

Genuine Honda Civic Trunk Lids

Deck Lids

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

78 Trunk Lids found

View related parts
Honda Civic Lid, Trunk
Part Number: 68500-TBA-A00ZZ
$579.48 MSRP: $836.18
You Save: $256.70 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 4 Door EX, 4 Door EX-A, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Lid, Trunk
Part Number: 68500-TBA-A10ZZ
$595.45 MSRP: $859.23
You Save: $263.78 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-TEG-A10ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo) | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Trunk Lid Comp
Part Number: 68500-TBG-A00ZZ
$547.74 MSRP: $790.38
You Save: $242.64 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2020 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo) | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Lid, Trunk
Part Number: 68500-TR3-A70ZZ
$841.64 MSRP: $1214.49
You Save: $372.85 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-TR6-A70ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2015 Honda Civic | 4 Door EX, 4 Door EX-L | KA CVT, KL CVT
View related parts
Honda Civic Lid Comp,Trunk(DOT)
Part Number: 68500-TR3-A90ZZ
$662.98 MSRP: $956.68
You Save: $293.70 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-TR3-A00ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012 Honda Civic | 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door LX, 4 Door LX (AT) | KA 5AT, KA 5MT, KL 5AT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-TR7-A80ZZ
$695.10 MSRP: $1003.03
You Save: $307.93 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013 Honda Civic | 4 Door SI | KA 6MT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SNH-C90ZZ
$444.48 MSRP: $641.38
You Save: $196.90 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SNC-A80ZZ, 68500-SNC-A10ZZ, 68500-SNH-C10ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Honda Civic | 4 Door MX (Hybrid) | KA CVT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-S5D-A92ZZ
$537.69 MSRP: $800.13
You Save: $262.44 (33%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-S5D-A91ZZ, 68500-S5D-A90ZZ, 68500-S5A-A91ZZ, 68500-S5D-A00ZZ, 68500-S5A-A90ZZ, 68500-S5A-A00ZZ, 68500-S5D-A01ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2001-2005 Honda Civic | 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door GX, 4 Door LX, 4 Door LX-CAR | KA 4AT, KA 5MT, KA CVT, KL 4AT, KL 5MT
View related parts
Honda Civic Lid, Trunk
Part Number: 68500-TR3-A30ZZ
$829.94 MSRP: $1197.59
You Save: $367.65 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-TR5-A90ZZ, 68500-TR6-A30ZZ, 68500-TR3-306ZZ, 68500-TR5-A30ZZ, 68500-TR6-306ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2015 Honda Civic | 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door LX | KA 5AT, KA 5MT, KA CVT, KL 5AT, KL CVT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SNE-A90ZZ
$551.71 MSRP: $796.11
You Save: $244.40 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SNE-A00ZZ, 68500-SNA-A00ZZ, 68500-SNA-A90ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2011 Honda Civic | 4 Door DX, 4 Door EX, 4 Door GX, 4 Door LX | KA 5AT, KA 5MT
View related parts
Honda Civic Lid Assy., L. Trunk Side *NH900L* (DEEP BLACK)
Part Number: 84655-TGG-A01ZA
$138.24 MSRP: $196.92
You Save: $58.68 (30%)
ADD TO CART
Product Specifications
- Other Name: Lid Assy., L. Trunk Side *NH900L*; Lid Trim
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door EX, 5 Door EX-L, 5 Door Sport, 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring) | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic LID, TRUNK
Part Number: 68500-TBF-A01ZZ
$539.44 MSRP: $778.42
You Save: $238.98 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-TBF-A00ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Civic | 4 Door SI | KA 6MT
View related parts
Honda Civic LID, TRUNK
Part Number: 68500-T20-A00ZZ
$587.78 MSRP: $848.16
You Save: $260.38 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022-2023 Honda Civic | EX, LX, Sport, Touring
View related parts
Honda Civic Lid Assy., L. Trunk Side *NH900L* (DEEP BLACK)
Part Number: 84655-TGG-A51ZA
$82.88 MSRP: $117.07
You Save: $34.19 (30%)
ADD TO CART
Product Specifications
- Other Name: Lid Assy., L. Trunk Side *NH900L*; Lid Trim
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door LX, 5 Door SE, 5 Door Sport | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SNH-C80ZZ
$473.82 MSRP: $683.72
You Save: $209.90 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SNH-C00ZZ, 68500-SNC-A90ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2009-2011 Honda Civic | 4 Door LX-S | KA 5AT, KA 5MT
- 2006-2007 Honda Civic | 4 Door MX (Hybrid) | KA CVT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SNX-A80ZZ
$444.48 MSRP: $641.38
You Save: $196.90 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SNX-A10ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Honda Civic | 4 Door SI | KA 6MT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-S5B-A90ZZ
$350.93 MSRP: $575.02
You Save: $224.09 (39%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Honda Civic | 4 Door MX (Hybrid) | KA 5MT, KA CVT, KL 5MT, KL CVT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-TS8-A50ZZ
$695.10 MSRP: $1003.03
You Save: $307.93 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013 Honda Civic | 2 Door EX, 2 Door EX-L | KA 5AT, KA 5MT, KL 5AT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SNE-A80ZZ
$465.82 MSRP: $672.18
You Save: $206.36 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SNE-A10ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Honda Civic | 4 Door EX, 4 Door EX-L | KA 5AT, KA 5MT
View related parts
Honda Civic Lid, Trunk (DOT)
Part Number: 68500-SVA-A61ZZ
$635.56 MSRP: $917.12
You Save: $281.56 (31%)
ADD TO CART
Product Specifications
- Other Name: Trunk Lid
- Replaces: 68500-SVA-A60ZZ, 68500-SVA-A30ZZ, 68500-SVA-A81ZZ, 68500-SVA-A80ZZ, 68500-SVA-A10ZZ, 68500-SVA-A31ZZ
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2011 Honda Civic | 2 Door EX, 2 Door EX-L | KA 5AT, KA 5MT

| Page 1 of 4 |Next >

1-20 of 78 Results

Honda Civic Trunk Lids

In search of affordable OEM Honda Civic Trunk Lids? Consider browsing through our extensive inventory of genuine Honda Civic Trunk Lids. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Civic Trunk Lids Parts Questions & Experts Answers

Lid, Trunk
68500-TR3-A70ZZ
Q: How should the trunk lid be removed and installed safely and correctly on Honda Civic?
A: The trunk lid is heavy and somewhat awkward to remove and install, so at least two people should perform this procedure. To begin, open the trunk lid and cover the edges of the trunk compartment with pads or cloths to protect the painted surfaces. Disconnect any cables or wire harness connectors attached to the trunk lid that would interfere with removal. If equipped, remove the hinge trim cover and make alignment marks around the hinge by drawing around it and the bolts with a marking pen before loosening the bolts to ensure proper alignment when reinstalling. While an assistant supports the trunk lid, remove the lid-to-hinge bolts on both sides and lift it off. For installation, follow the reverse of the removal process, ensuring to align the lid-to-hinge bolts with the marks made earlier. For adjustment, fore-and-aft and side-to-side alignment of the trunk lid can be achieved by moving it in relation to the hinge after loosening the bolts or nuts. Scribe a line around the hinge plate to determine the amount of movement, then loosen the bolts and adjust the trunk lid into the correct alignment, tightening the hinge bolts or nuts afterward to check the alignment. If necessary, the entire trunk lid striker assembly can be adjusted up and down as well as from side to side by loosening two bolts to reposition the striker, marking its location for reference. Scribe a line around the striker assembly for guidance, then reposition as needed and retighten the mounting bolts. Periodically lubricate the trunk lid latch assembly and hinges with white lithium-base grease to prevent sticking and wear. Finally, adjust the height of the trunk lid in relation to the body by screwing the rubber bumpers in or out.